LG Electronics GDK-20W Isdn STIB2 & Stib S/T Interface Board Installation, SW2 SW1 CN2

Page 27

GDK-20W DIGITAL WIRELESS KEY TELEPHONE SYSTEM

Analog CO/PABX Line Interface Boards (LCOB: Loop-start) Installation

The LCOB2, LCOB, LCOBE, LCOBA, and LCOB4 can be installed on the SLOT2 & SLOT3

The exterior of them are shown in Figure 3.4.7.

This board provides two(2) Loop Start ports and four(4) Loop Start ports.

Board

Slot

Port No.

 

 

 

LCOB2, LCOB4

SLOT2 & 3

4

 

 

 

LCOB, LCOBE, LCOBA

SLOT2 & 3

2

 

 

 

[Table 3.4.2] LCOBs

Figure 3.4.7 Analog CO Interface Boards

ISDN STIB2 & STIB (S/T Interface Board) Installation

It should be noted that the STIB2 & STIB board should be installed on the SLOT2&SLOT3 of the MBU.

The STIB2 provides 1 port of BRI(Basic Rate Interface-‘T’ mode only) and 1port of ‘S’ and ‘T’ mode Switchable interface and STIB provides 1 port of ‘S’ and ‘T’ mode Switchable interface.

Select the jumpers and DIP switches for S0 or T0 interface. Be sure to connect ISDN trunk to T0 interface port and ISDN extension to S0 interface port. Check if ISDN trunk is not connected to S0 interface port and ISDN extension is not connected to T0 interface port.

The mode selection method is shown in table 3.4.3.

S/T Port

S/T Port

T Port

SW2

 

SW1

CN2

1 Port STIB

SW2

 

SW1

CN2

2 Port STIB

SW3

Figure 3.4.8 Switches and connector for the STIB

29

Image 27
Contents Digital Wireless Key Telephone System Installation Manual Revision History Table of Contents Admin Programming Regulatory Information PurposeInterference and Attenuation Replacement of Lithium BatteriesHearing AID Compatibility PicturesAbbreviations Introduction MFB System CapacityIsdn BRI PMUSTA Isdn1 Dimensions & Weights Height Width Depth System SpecificationsFlash Memory 4 Electrical Specifications AWG WireLcobesp System ComponentsRing Generation UnitRGU Key Service Unit KSUMain Board Unit MBU Program Module Unit PMUWireless Terminal Interface Board Wtib Interface Board STIB2Interface Board Stib Dvib Digitized Voice Interface Board General Site Considerations Site PreparationVerify On-Site Equipment Back-Board InstallationMounting the KSU KSU & Power Installation2 KSU Mounting Holes & Installation layout Power InstallationKSU Grounding PCB Installation PCB Handling & General InstallationMain Board Unit MBU Installation 2 MBU Installation OFF PMU Installation MFB Installation RGU InstallationSW2 SW1 CN2 Isdn STIB2 & Stib S/T Interface Board InstallationSW1 CN2SW2 SW2Dvib Digitized Voice Interface Board Installation Wtib Wireless Terminal Interface Board Installation11 Connectors of the Dvib Battery Back-Up Wiring Installation System WiringGeneral Purpose Relays Wiring Music on Hold MOH WiringFerrite Core Installation Alarm Detect Port Wiring4 Ferrite core on signal wires Components of the Dect system Overview of the Dect system1 Components of a Dect system GDK-20W Digital Wireless Key Telephone System Wtib Wireless Terminal Interface BoardBase Station GDC-200B Terminating a Call How to make CallsBefore Making Initial Call Controlling a CallBase Station GDK-20W DectAntenna Diversity Subscription Low Battery Alarm 8 Single-Slot Charger 330-SSC, 340-SSC System Configuration Before InstallationSite Survey Base Station Broadcast Range and Location 9 Base Station Service AreaGeneral Guidelines CRSCell-Coverage Region Survey ToolDistance Fading Reporting Results Rssi Monitoring Possible in GDC-335H onlyCheck list for Survey Data Korea Dect Survey Report Template NumberExamples Example 1 Centralizing Base StationsExample 2 Base Station Coverage in Adjoining Areas 15 Location of Base Station in Office Environment Example 3 Maximizing Line of SiteEquipment Check Hardware InstallationWtib Installation Unit Installation18 Wall Mounting of Base Station without wedge 20 LCD Message of Unsubscribed GDC-335H GAP and GDC-340HGAP System ID User subscription/desubscriptionConditions Authentication CodeAt the GDC-335H User SubscriptionAC code + User Desubscription At the GDC-340H Menuup or Down Summary of Dect Installation Stib Isdn DescriptionBasic Features of Isdn Device S-Interface GDK-20W Digital Wireless KEY Telephone System Features of Isdn CO Line T-Interface Unknown / National Type / International / Subscriber System Capacities GDK-20WRemark Numbering PLAN*1 Feature CodesTRANS/PGM+*1 TRANS/PGM+#4MON+DND/FOR+7 MON+DND/FOR+#SLT, DND SLT/WHTU*2 Features Basic Extension RemarksBasic and Extended Numbering Plans LCD MonthsSLT Ring Cadence Audible SignalsTone / Ring Cadence SLTFrequencies and Tones GDK-20W Digital Wireless KEY Telephone System Maximum Number of CO Lines in GDK-20W 8 Ports GDK-20W ConfigurationGDK-20W Station Configuration with LKD 2B Maximum Number of Stations in GDK-20W 34 PortsGain Controlsystem Basemain Menu 5 SUB Menu Wireless Cell / Terminal ConfigurationNumber of Ports Default Number Description Maximum Number of Ports Station / CO in GDK-20W 38 PortsSLT Rx Gain Country CIS Dktu SLT DCOSLT DCO Introduction To Enter the Programming ModeAdmin Program Start Press Flex KEY1-12 General DescriptionTERMINAL-MENU HOW to ProgramMAIN-MENU SUB-MENUYES Example of Admin. ProgramProcedure DNDStation Attribute Button DefinitionAdmin Programming Admin Programming IndexFlex KEY Main Menu SUB Menu SYS TMR SYS PGMUCD SUB Menu Flex KEY Terminal Menu Range Default Remark Default ValuesLoop Didrn SUB Menu Flex Terminal Menu Range Default Remark KEYPBX / CO Isdn CO Colp2.3 Isdn Program Main Menu Flex SUB Menu Terminal Range Default Remark KEYSYS / EXC DID/DISASmdr MUSIC1 DktuDtmf RX ToneYES/NO DVU SUB Flex SUB Menu Range Default Remark KEY TimerFlex KEY SUB Menu Terminal Menu Default Remark DMT Flex KEY SUB Menu Range Default RemarkDisable Override Always LDT2.10 Hunt GROUP/VOICE Mail Program Main Menu