Radio Shack TAD-1006 owner manual Problem Solving, Problem Cause Remedy

Page 30

43-768.fm Page 30 Friday, August 13, 1999 2:49 PM

PROBLEM SOLVING

We do not expect you to have any problems with your TAD-1006, but if you do, try these suggestions. If the TAD-1006 still does not operate as you think it should, take it to your local Radio Shack store for assistance.

Problem

Cause

Remedy

 

 

 

 

 

 

The TAD records a dial

The caller hung up without

Press NEXT (or 9

tone, siren, beeping, or

leaving a message or without

remotely) to play the

an operator’s voice

using the maximum time, and

next message.

instead of the caller’s

your local telephone com-

 

message.

pany does not send out CPC

 

 

signals.

 

 

 

 

 

The phone line is not properly

Check all phone line

 

connected.

connections.

 

 

 

The TAD does not

The TAD is not plugged into

Make sure the AC

power.

adapter is properly

answer calls.

 

connected to the

 

 

 

 

TAD and to power.

 

 

 

 

The TAD is not set to answer

Press ON/OFF so the

 

calls.

ANSWER indicator

 

 

turns on.

 

 

 

 

You were too close to the TAD

Re-record the

 

or you spoke too loudly when

announcement,

 

recording the announcement.

speaking in a normal

The outgoing

 

tone of voice about

announcement

 

12 inches from the

is distorted.

 

TAD.

 

 

 

 

There was too much back-

Re-record the

 

ground noise in the room

announcement.

 

when you recorded the

 

 

announcement.

 

 

 

 

The TAD does not play

The outgoing announcement

Record a new outgo-

the outgoing

is less than 2 seconds long.

ing announcement

announcement you

 

that is at least 2 sec-

recorded.

 

onds, but no more

 

 

than 1 minute long.

 

 

 

30

 

 

Image 30
Contents TAD-1006 Features TelephoneOutgoing Message Remote Skip Read this Before Installation FCC StatementContents Resetting the TAD-1006 Installation Connecting the AC AdapterSelecting a Location Installing a Backup Battery Connecting the Wall Bracket MountingPlacing on a Desktop Mounting on a Wall Plate Mounting Directly on the Wall Connecting Handset Setting the TONE- Pulse SwitchUsing Redial Using Memory DialingTelephone Operation Storing a Number in Memory Storing a Pause in Memory Dialing a Stored NumberSetting the DAY Time TAD PreparationTurning the TAD ON/OFF Setting the Number of Rings Press one for AM, two for PMRecording Announcements Recording the Outgoing AnnouncementChecking/Deleting the Outgoing Announcement Recording the Memory Full AnnouncementChecking/Deleting the Memory Full Announcement Setting the TAD to ANSWER/NOT Answer Calls TAD OperationAnswering Calls Using the ANNOUNCEMENT-ONLY Feature Recording Announcement-Only MessageTurning Announcement-Only On/Off Screening Calls Recording a 2-WAY ConversationChecking/Deleting Announcement-Only Message Recording a Memo Playing MessagesPlaying Incoming Messages Playing 2-Way ConversationsPlaying Memos Deleting Messages To delete all incoming messagesUsing the TOLL-SAVER Remote TAD OperationChanging Remote Code Using Remote Commands Remote ANSWER-ONFm Page 28 Friday, August 13, 1999 249 PM List of Remote Commands PressProblem Solving Problem Cause RemedyFm Page 31 Friday, August 13, 1999 249 PM Resetting Care and Maintenance FCC Wants YOU to Know LightningFm Page 35 Friday, August 13, 1999 249 PM Radio Shack

TAD-1006 specifications

The Radio Shack TAD-1006 is a notable technological artifact from the late 1980s and early 1990s that reflects the intersection of telecommunications and user-oriented design. This telephone answering device (TAD) was part of a broader trend in consumer electronics, aiming to enhance communication convenience for households.

One of the main features of the TAD-1006 is its ability to store and playback voice messages. The device uses a compact cassette mechanism to record audio messages, which was a common technology at the time. Users appreciated the straightforward operation, as the device allowed them to easily set up, record, and retrieve messages. With a recording time of approximately 15 minutes, the TAD-1006 could accommodate multiple messages, enabling users to manage their communications effectively.

The TAD-1006 also boasted a built-in speaker, facilitating easy playback of recorded messages without needing to connect to an external audio system. This feature, along with adjustable volume controls, ensured that users could play back messages at their desired sound level. Additionally, the unit came equipped with indicators and lights that helped users quickly identify when new messages were available, which enhanced the overall user experience.

In terms of technology, the TAD-1006 integrated a feature called "remote access," allowing users to check their messages from a remote location. This was a revolutionary aspect at the time, giving users the freedom to manage their voicemail even when they were away from home. The operation was simplified with a designated phone code, ensuring accessibility without the need for complex setups.

Durability and user-friendliness were paramount in the design of the TAD-1006, which featured an intuitive button layout for easy navigation through its various functionalities. The device was compact enough to fit comfortably on a desk or shelf while retaining a vintage aesthetic that appealed to many users of that era.

In summary, the Radio Shack TAD-1006 represented a significant development in personal communication technology. Its combination of features, including voice message storage, remote access capabilities, and ease of use, made it a popular choice among families looking to streamline their communication. Even today, the TAD-1006 stands as a nostalgic reminder of the era of analog voicemail systems and represents an important chapter in the evolution of answering machines.