Agilent Technologies Option 100, E2625A manual Document Warranty

Page 48

Notices

© Agilent Technologies, Inc. 1999-2002

No part of this manual may be reproduced in any form or by any means (including electronic storage and retrieval or transla- tion into a foreign language) without prior agreement and written consent from Agilent Technologies, Inc. as governed by United States and interna- tional copyright laws.

Manual Part Number

E2625-97003, March 2002

Print History

E2625-97003, March 2002

E2625-97002, January 2000

E2625-97001, October 2000

E2625-97000, May 1999

Agilent Technologies, Inc.

1601 California Street

Palo Alto, CA 94304 USA

Restricted Rights Legend

If software is for use in the per- formance of a U.S. Government prime contract or subcontract, Software is delivered and licensed as “Commercial com- puter software” as defined in DFAR 252.227-7014 (June 1995), or as a “commercial item” as defined in FAR 2.101(a) or as “Restricted computer software” as defined in FAR 52.227-19 (June 1987) or any equivalent agency regulation or contract clause. Use, duplication or dis- closure of Software is subject to Agilent Technologies’ standard commercial license terms, and non-DOD Departments and Agencies of the U.S. Govern- ment will receive no greater than Restricted Rights as defined in FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2) (November 1995), as applicable in any technical data.

Document Warranty

The material contained in this document is provided “as is,” and is subject to being changed, without notice, in future editions. Further, to the maximum extent permitted by applica- ble law, Agilent disclaims all warranties, either express or implied, with regard to this manual and any information contained herein, including but not limited to the implied war- ranties of merchantability and fitness for a particular purpose. Agilent shall not be liable for errors or for inci- dental or consequential damages in connection with the furnishing, use, or per- formance of this document or of any information con- tained herein. Should Agi- lent and the user have a separate written agreement with warranty terms cover- ing the material in this docu- ment that conflict with these terms, the warranty terms in the separate agreement shall control.

Technology Licenses

The hardware and/or software described in this document are furnished under a license and may be used or copied only in accordance with the terms of such license.

WARNING

A WARNING notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in personal injury or death. Do not proceed beyond a WARNING notice until the indicated conditions are fully understood and met.

CAUTION

A CAUTION notice denotes a hazard. It calls attention to an operating procedure, practice, or the like that, if not correctly performed or adhered to, could result in damage to the product or loss of important data. Do not proceed beyond a CAUTION notice until the indicated conditions are fully understood and met.

Trademark Acknowledgements

Windows and MS Windows are U.S. registered trademarks of Microsoft Corporation.

Image 48
Contents User’s Guide Getting Started and Using Masks This BookContents Contents-2 Page Adding Option 100 to an existing Infiniium Oscilloscope Recommended accessories Supplied itemsWhat not to do Oscilloscope models Channels Bandwidth Sample RateTo access the Mask Test Setup dialog box Overview of the Mask Test Setup dialog box Is enabledGetting Started and Using Masks Getting Started and Using Masks Introduction to Mask TestingHow Infiniium does Mask Testing Make a copy of the Mask Test diskTo install the Standard Masks Load Mask dialog box will resembleTo calibrate the oscilloscope Cal Memory ProtectTo choose a proper probe for Mask Testing Calibrating the probe adapterTo get your waveform on the oscilloscope display To enable the Mask Test To load a Mask Locate the Use File Setup When Aligning option To align a Mask to the waveformStarts mask test in the Mask Test Setup dialog box To start and stop the Mask TestTo understand the Mask Test tab description area To run the Mask Test conditionally To stop the Mask Test on the first failure Analyzing a failureStandard Masks Standard Masks Pre-Compliance Sonet Masks ITU G.703 International Standard Masks 2MbITU75.msk 6312kbITU110DS2.msk 6312kbITU75DS2.msk 8MbITU.msk 34MbITU.msk 44736kbITUDS3.msk 140MbITU0.msk 140MbITU1.msk 140MbITU1INV.msk 155MbITU0.msk 155MbITU1.msk 155MbITU1INV.msk Ansi T1.102 North American Standard Masks DS1CANSI.msk DS2ANSI.msk DS3ANSI.msk DS4NAANSI.msk DS4NAANSIMAX.msk STS1ANSIEYE.msk STS1ANSIPULSE.msk STS3ANSI.msk STS3ANSIMAX.msk FCC Part 68.308 Options A, B, and C Masks FCC68OPTC.msk Pre-Compliance Sonet Masks OC12SONET.msk Ieee 802.3 Masks 100BASETXSTP 100BASETXUTP Safety Document Warranty