Siemens 6220, 6210 Using Network Features, Conferencing a Held Call, Dropping the Last Party

Page 13

Conferencing a Held Call

Press the Conf key while you are on an active call with another call on hold.

The current call is placed on hold and an idle call appearance is automatically selected. The Conf indicator lights.

Press the Call Appearance key for the held call you wish to add to the conference.

Press the Conf key to conference all parties together.

Repeat the above steps to add another party.

Dropping the Last Party

Press the Drop key to remove the last party added to a conference.

Terminating a Conference

Replace the handset or press the Spkr key to terminate a conference, removing yourself and all other parties.

Depending on your network configuration, other parties in the conference may remain connected or be disconnected.

Using Network Features __________________

Feature Activator keys access features provided by the telephone network. A feature is active when the key’s red indicator is on.

Some commonly available features are listed below. Consult your service provider for more information.

Call Forwarding

Forwards ringing calls to another number. When the Call Forward key indicator is lit, incoming calls will be forwarded.

10Tone Commander 6210/6220 User Manual

Image 13

Contents Page Contents Appendix a Ordering Isdn Service Introduction General FeaturesModels/Options Controls and Indicators OFF Page Placing a Call OperationSelecting a Call Appearance DialingLast Number Redial Answering a Call Using DSS KeysCall Preference Ringing ControlDisplaying Call Appearance Information Bridging a Shared Call AppearanceHolding Calls Conferencing Calls Transferring CallsDSS Transfer Conferencing a New CallConferencing a Held Call Using Network FeaturesDropping the Last Party Terminating a ConferenceUsing the Call Log Call Menu DIR LOG ID Viewing the Call LogSelect Call LOG Type Unans Answd OUT Delete Dial Time BackDialing a Call Log Entry Shortcut to the Unanswered Call LogWhat is the Call Directory? Using the Call DirectoryDialing from the Call Directory Directory PAGE1\Placing and Answering Calls Using the SpeakerphoneMuting the Microphone Enabling/Disabling Using Voice AnnounceReceiving Voice Announce Calls Adjusting the Receive Volume Using a HeadsetAdjusting the Ringer Volume Headset Mode OperationOrdering Isdn Service Installation6210T/6220T Installation Set the Termination Switches on the Telephone and NT1Basic Multipoint Line and Power ConnectionsShort Multipoint Extended Point-to-PointHandset/Headset Pin # Signal Wire ColorSet the Termination Switch on the Telephone 6210U/6220U InstallationVolt 6210U Power Supply 6220U Rotating the Base Wall MountingAttaching to a wall mount jack L3OK SWITCH=5ESS NI-X Configure the SetInitialization L1OKFirmware Updates No Parameter Download Press Setup to ConfigureUsing Local Inspect to Verify Keys Automatic Button Detection 5ESS Custom Isdn onlyPersonal Ringing Customize your PhoneLabel the Set Installation Options Menu Installation OptionsSetup Menu Instl Admin User Pots Installation Options \ Spid Param KeysBksp Clear Spid EntryParameter Download Configuring KeysStarting a Download Enabling/Disabling Automatic DownloadUnused CA/DN FA DSS SpdialCall Appearance / Directory Number Keys Bksp Orig ReservAutomatic Call Appearance Selection 10=NETWORK FA#59 Call Bkspcall Feature Activator KeysBksp Clear Pause DSS KeysBksp Clear Pause FA Speed Dial KeysBksp Pause FA Terminal MODE=CACH Ekts Cach Basic Terminal ModeInstallation Password SET Clear Installation PasswordNEW Password Bksp Verify Password BkspPassword Cleared Removing the PasswordWhat to do if you lose your password Reset ALL Setup OPTIONS? YES no Reset to Factory Default SettingsALL Settings Cleared Voice Announce Options Voice AnnounceSelecting CA/DN Keys Select VA Keys GREEN=VA, RED=AVAILABLEBksp Clear ALL Selecting Incoming Directory NumbersALERTING=ANY Normal Dist Intcom PRI Selecting Alerting PatternsAutomatic MUTE=ON On OFF Automatic MutingAdministration Options Menu Administration OptionsAdministration Options \ Inspct Vers Test Diag Administration Options \ Restart LOGLocal Inspect Local InspectKeys Call Appearance/Directory Number KeyOriginating DN? YES \ RESERVED=OUT/PRIORITY Feature Activator, Conference, Transfer, or Drop KeyOriginating DN? no RESERVED=NOT Reserved DSS KeyDirectory Numbers Message Waiting IndicatorMESSAGE=NETWORK FI#63 Speed Dial KeyVersion Serial H/W S/W VersionSerial Number Hardware VersionMODEL6030X Button Expan Optional Equipment VersionTest Display and LED IndicatorsTerminal Test Disply Keys DISPLAY/LED Test LCD RED Green OFFKEY Test Passed Press ANY KEY to Exit Press Each KEY to Test Or GO OFF-HOOK to Exit6030X Expansion Module Press Each KEY on Press Done to ExitRestart Diagnostic DisplayRESTART/CLEAR Call LOG? YES no View LOG Entries Error Param Clear Viewing the Error and Download LogsClearing Logs User Options Menu User OptionsUser Options Clock Spdial DIR Ring User OptionsSetting Up Speed Dial Keys Setting the Time and DateBKSPAM/PM Smart Pauses Speed Dial ProgrammingSelect a Softkey PAGE1\ Setting Up the Call DirectoryBksp Clear Move Number Moving a Directory Entry Bksp Clear Pause NamePick NEW Softkey PAGE1\ Deleting a Directory EntryRinging Tone Personal Ringing OptionsRinging TONE=5 USE Keypad Keys Off-Hook Ringing OptionsRinging Control for Individual Call Appearances Call PREFERENCE=RINGING Ring Idle None Call Preference OptionsHandset/Headset Mode Handset/Headset ConfigurationVoice MODE=HEADSET Hand Head Volume Preset Volume LevelsReceive handset and headset Adjusting the Display ContrastTransmit headset only Call LOG Password SET Clear Setting a Call Log PasswordCreating/Changing Your Password Verify NEW Password BkspRemoving the Password Inoperable Telephone Recovery Procedures TroubleshootingWith full initialization, proceed to the following steps CA/DN trouble Check Fix Telephone Configuration TroubleshootingSetup Wizard Ordering Isdn ServiceWhere to Go for Help Ordering ManuallyNetwork Assignment Button # Recommended Button AssignmentsInstl Installation Options Setup Menu TreeAdmin Administration Options User User Options Pots 6002TA Analog Pots Port Options Tone Commander Product Warranty Warranty and ServiceSpecifications Parameter Default Value National Isdn 5ESS Custom Isdn Factory Default SettingsUL/FCC Statements Important Safety InstructionsPage FCC Requirements Page Page 13-102800 Rev. L