Siemens 6210, 6220 user manual Shortcut to the Unanswered Call Log, Dialing a Call Log Entry

Page 16

Shortcut to the Unanswered Call Log

If any calls ringing at your telephone were unanswered, UNANS will appear in the display. You can select UNANS to enter directly into the Unanswered call log. After you have viewed the unanswered call log, the UNANS display indication will clear until new calls are received.

Dialing a Call Log Entry

With the call you want to dial showing in the call log display, select DIAL.

An idle call appearance will be automatically selected. The directory number from the log will be shown in the second line of the display. For outgoing calls, all digits that were dialed to complete the original call are shown.

3=Dial:

4253491234

Add any required prefixes, then press the softkey under the directory number to dial the digits displayed.

3=91

4253491234

Tone Commander 6210/6220 User Manual

13

Image 16
Contents Page Contents Appendix a Ordering Isdn Service Introduction General FeaturesModels/Options Controls and Indicators OFF Page Operation Placing a CallSelecting a Call Appearance DialingLast Number Redial Using DSS Keys Answering a CallCall Preference Ringing ControlDisplaying Call Appearance Information Bridging a Shared Call AppearanceHolding Calls Transferring Calls Conferencing CallsDSS Transfer Conferencing a New CallUsing Network Features Conferencing a Held CallDropping the Last Party Terminating a ConferenceUsing the Call Log Viewing the Call Log Call Menu DIR LOG IDSelect Call LOG Type Unans Answd OUT Delete Dial Time BackShortcut to the Unanswered Call Log Dialing a Call Log EntryUsing the Call Directory What is the Call Directory?Dialing from the Call Directory Directory PAGE1\Placing and Answering Calls Using the SpeakerphoneMuting the Microphone Enabling/Disabling Using Voice AnnounceReceiving Voice Announce Calls Using a Headset Adjusting the Receive VolumeAdjusting the Ringer Volume Headset Mode OperationInstallation Ordering Isdn Service6210T/6220T Installation Set the Termination Switches on the Telephone and NT1Line and Power Connections Basic MultipointShort Multipoint Extended Point-to-PointPin # Signal Wire Color Handset/Headset6210U/6220U Installation Set the Termination Switch on the TelephoneVolt 6210U Power Supply 6220U Rotating the Base Wall MountingAttaching to a wall mount jack Configure the Set L3OK SWITCH=5ESS NI-XInitialization L1OKNo Parameter Download Press Setup to Configure Firmware UpdatesUsing Local Inspect to Verify Keys Automatic Button Detection 5ESS Custom Isdn onlyCustomize your Phone Personal RingingLabel the Set Installation Options Installation Options MenuSetup Menu Instl Admin User Pots Installation Options \ Spid Param KeysSpid Entry Bksp ClearConfiguring Keys Parameter DownloadStarting a Download Enabling/Disabling Automatic DownloadCA/DN FA DSS Spdial UnusedCall Appearance / Directory Number Keys Bksp Orig ReservAutomatic Call Appearance Selection Feature Activator Keys 10=NETWORK FA#59 Call BkspcallDSS Keys Bksp Clear PauseBksp Clear Pause FA Speed Dial KeysBksp Pause FA Terminal Mode Terminal MODE=CACH Ekts Cach BasicInstallation Password Installation Password SET ClearNEW Password Bksp Verify Password BkspPassword Cleared Removing the PasswordWhat to do if you lose your password Reset ALL Setup OPTIONS? YES no Reset to Factory Default SettingsALL Settings Cleared Voice Announce Voice Announce OptionsSelecting CA/DN Keys Select VA Keys GREEN=VA, RED=AVAILABLESelecting Incoming Directory Numbers Bksp Clear ALLSelecting Alerting Patterns ALERTING=ANY Normal Dist Intcom PRIAutomatic Muting Automatic MUTE=ON On OFFAdministration Options Administration Options MenuAdministration Options \ Inspct Vers Test Diag Administration Options \ Restart LOGLocal Inspect Local InspectKeys Call Appearance/Directory Number KeyFeature Activator, Conference, Transfer, or Drop Key Originating DN? YES \ RESERVED=OUT/PRIORITYOriginating DN? no RESERVED=NOT Reserved DSS KeyMessage Waiting Indicator Directory NumbersMESSAGE=NETWORK FI#63 Speed Dial KeyVersion Version Serial H/W S/WSerial Number Hardware VersionOptional Equipment Version MODEL6030X Button ExpanDisplay and LED Indicators TestTerminal Test Disply Keys DISPLAY/LED Test LCD RED Green OFFPress Each KEY to Test Or GO OFF-HOOK to Exit KEY Test Passed Press ANY KEY to Exit6030X Expansion Module Press Each KEY on Press Done to ExitRestart Diagnostic DisplayRESTART/CLEAR Call LOG? YES no View LOG Entries Error Param Clear Viewing the Error and Download LogsClearing Logs User Options User Options MenuUser Options Clock Spdial DIR Ring User OptionsSetting Up Speed Dial Keys Setting the Time and DateBKSPAM/PM Speed Dial Programming Smart PausesSelect a Softkey PAGE1\ Setting Up the Call DirectoryBksp Clear Move Number Bksp Clear Pause Name Moving a Directory EntryPick NEW Softkey PAGE1\ Deleting a Directory EntryPersonal Ringing Options Ringing ToneRinging TONE=5 USE Keypad Keys Off-Hook Ringing OptionsRinging Control for Individual Call Appearances Call Preference Options Call PREFERENCE=RINGING Ring Idle NoneHandset/Headset Configuration Handset/Headset ModeVoice MODE=HEADSET Hand Head Volume Preset Volume LevelsReceive handset and headset Adjusting the Display ContrastTransmit headset only Setting a Call Log Password Call LOG Password SET ClearCreating/Changing Your Password Verify NEW Password BkspRemoving the Password Troubleshooting Inoperable Telephone Recovery ProceduresWith full initialization, proceed to the following steps Telephone Configuration Troubleshooting CA/DN trouble Check FixOrdering Isdn Service Setup WizardWhere to Go for Help Ordering ManuallyRecommended Button Assignments Network Assignment Button #Setup Menu Tree Instl Installation OptionsAdmin Administration Options User User Options Pots 6002TA Analog Pots Port Options Warranty and Service Tone Commander Product WarrantySpecifications Factory Default Settings Parameter Default Value National Isdn 5ESS Custom IsdnImportant Safety Instructions UL/FCC StatementsPage FCC Requirements Page Page 13-102800 Rev. L