Siemens 6210, 6220 user manual Wall Mounting, Rotating the Base, Attaching to a wall mount jack

Page 26

Wall Mounting __________________________

Robust handset retainer clips for wall mount use are available on request from Tone Commander.

Rotating the Base

The phone base must be rotated for wall mounting.

•Disconnect the line cord.

•Remove the retaining screw in the center of the base.

•Press the top of the tall edge of the base to disengage the snap tabs, then lift the base from the telephone body.

Do not touch the expansion connector. If using the 6030X, 6001TA, or 6002TA, leave the expansion cable plugged into the phone.

•Turn the base 180°, insert the tabs on the short edge of the base into the holes near the display end of the telephone, and then snap the tall side of the base onto the telephone.

•Replace the retaining screw (required for UL compliance).

Attaching to a wall mount jack

•Plug an 8”, 8-pin line cord into the S/T IN jack (6210/6220T) or the U IN jack (6210/6220U) on the telephone. Route the cord under the guide tabs on the base. If you do not have one, you can obtain an 8” line cord by calling Tone Commander Technical Support at

(800) 524-0024.

•Hold the telephone next to the wall mount jack. Plug the line cord into the jack.

•Hang the telephone on the wall plate mounting studs. Press down firmly to lock in place.

•Push any excess line cord into the base.

Tone Commander 6210/6220 User Manual

23

Image 26

Contents Page Contents Appendix a Ordering Isdn Service Models/Options General FeaturesIntroduction Controls and Indicators OFF Page Selecting a Call Appearance OperationPlacing a Call DialingLast Number Redial Call Preference Using DSS KeysAnswering a Call Ringing ControlHolding Calls Bridging a Shared Call AppearanceDisplaying Call Appearance Information DSS Transfer Transferring CallsConferencing Calls Conferencing a New CallDropping the Last Party Using Network FeaturesConferencing a Held Call Terminating a ConferenceUsing the Call Log Select Call LOG Type Unans Answd OUT Viewing the Call LogCall Menu DIR LOG ID Delete Dial Time BackShortcut to the Unanswered Call Log Dialing a Call Log EntryDialing from the Call Directory Using the Call DirectoryWhat is the Call Directory? Directory PAGE1\Muting the Microphone Using the SpeakerphonePlacing and Answering Calls Receiving Voice Announce Calls Using Voice AnnounceEnabling/Disabling Adjusting the Ringer Volume Using a HeadsetAdjusting the Receive Volume Headset Mode Operation6210T/6220T Installation InstallationOrdering Isdn Service Set the Termination Switches on the Telephone and NT1Short Multipoint Line and Power ConnectionsBasic Multipoint Extended Point-to-Point Pin # Signal Wire Color Handset/Headset6210U/6220U Installation Set the Termination Switch on the TelephoneVolt 6210U Power Supply 6220U Attaching to a wall mount jack Wall MountingRotating the Base Initialization Configure the SetL3OK SWITCH=5ESS NI-X L1OKUsing Local Inspect to Verify Keys No Parameter Download Press Setup to ConfigureFirmware Updates Automatic Button Detection 5ESS Custom Isdn onlyCustomize your Phone Personal RingingLabel the Set Setup Menu Instl Admin User Pots Installation OptionsInstallation Options Menu Installation Options \ Spid Param KeysSpid Entry Bksp ClearStarting a Download Configuring KeysParameter Download Enabling/Disabling Automatic DownloadCall Appearance / Directory Number Keys CA/DN FA DSS SpdialUnused Bksp Orig ReservAutomatic Call Appearance Selection Feature Activator Keys 10=NETWORK FA#59 Call BkspcallDSS Keys Bksp Clear PauseBksp Pause FA Speed Dial KeysBksp Clear Pause FA Terminal Mode Terminal MODE=CACH Ekts Cach BasicNEW Password Bksp Installation PasswordInstallation Password SET Clear Verify Password BkspWhat to do if you lose your password Removing the PasswordPassword Cleared ALL Settings Cleared Reset to Factory Default SettingsReset ALL Setup OPTIONS? YES no Selecting CA/DN Keys Voice AnnounceVoice Announce Options Select VA Keys GREEN=VA, RED=AVAILABLESelecting Incoming Directory Numbers Bksp Clear ALLSelecting Alerting Patterns ALERTING=ANY Normal Dist Intcom PRIAutomatic Muting Automatic MUTE=ON On OFFAdministration Options \ Inspct Vers Test Diag Administration OptionsAdministration Options Menu Administration Options \ Restart LOGKeys Local InspectLocal Inspect Call Appearance/Directory Number KeyOriginating DN? no RESERVED=NOT Reserved Feature Activator, Conference, Transfer, or Drop KeyOriginating DN? YES \ RESERVED=OUT/PRIORITY DSS KeyMESSAGE=NETWORK FI#63 Message Waiting IndicatorDirectory Numbers Speed Dial KeySerial Number VersionVersion Serial H/W S/W Hardware VersionOptional Equipment Version MODEL6030X Button ExpanTerminal Test Disply Keys Display and LED IndicatorsTest DISPLAY/LED Test LCD RED Green OFF6030X Expansion Module Press Each KEY to Test Or GO OFF-HOOK to ExitKEY Test Passed Press ANY KEY to Exit Press Each KEY on Press Done to ExitRESTART/CLEAR Call LOG? YES no Diagnostic DisplayRestart Clearing Logs Viewing the Error and Download LogsView LOG Entries Error Param Clear User Options Clock Spdial DIR Ring User OptionsUser Options Menu User OptionsBKSPAM/PM Setting the Time and DateSetting Up Speed Dial Keys Speed Dial Programming Smart PausesBksp Clear Move Number Setting Up the Call DirectorySelect a Softkey PAGE1\ Pick NEW Softkey PAGE1\ Bksp Clear Pause NameMoving a Directory Entry Deleting a Directory EntryRinging TONE=5 USE Keypad Keys Personal Ringing OptionsRinging Tone Off-Hook Ringing OptionsRinging Control for Individual Call Appearances Call Preference Options Call PREFERENCE=RINGING Ring Idle NoneVoice MODE=HEADSET Hand Head Volume Handset/Headset ConfigurationHandset/Headset Mode Preset Volume LevelsTransmit headset only Adjusting the Display ContrastReceive handset and headset Creating/Changing Your Password Setting a Call Log PasswordCall LOG Password SET Clear Verify NEW Password BkspRemoving the Password Troubleshooting Inoperable Telephone Recovery ProceduresWith full initialization, proceed to the following steps Telephone Configuration Troubleshooting CA/DN trouble Check FixWhere to Go for Help Ordering Isdn ServiceSetup Wizard Ordering ManuallyRecommended Button Assignments Network Assignment Button #Setup Menu Tree Instl Installation OptionsAdmin Administration Options User User Options Pots 6002TA Analog Pots Port Options Warranty and Service Tone Commander Product WarrantySpecifications Factory Default Settings Parameter Default Value National Isdn 5ESS Custom IsdnImportant Safety Instructions UL/FCC StatementsPage FCC Requirements Page Page 13-102800 Rev. L