Siemens 6220, 6210 user manual Configure the Set, Initialization, L1OK, L3OK SWITCH=5ESS NI-X

Page 27

Configure the Set _______________________

ISDN configuration is performed automatically in many cases. The telephone set will detect the switch type, set the SPID number, and download other setup parameters when these features are available from the central office.

You will be prompted for any required setup information that cannot be set automatically.

Initialization

A self-test is performed upon power up. Press any key to begin initialization with the network. Unattended initialization begins automatically after a short random time interval. This delay prevents multiple terminals at a site from initializing simultaneously after a power outage.

The display will show progress while establishing the communication layers. When all three communication layers are established, the TEI (Terminal Equipment Identifier) and switch type will be shown for two seconds.

L1:OK

L2:OK TEI:123

L3:OK

SWITCH=5ESS NI-X

SPID Entry

The SPID number will be assigned automatically if the network supports AutoSPID. If there is more than one SPID available for your terminal, you will be prompted to select your primary telephone number.

If AutoSPID is not supported, you will be prompted to enter the phone’s primary telephone number, which is used by the phone to generate a SPID number. Enter the number with the dial pad, then press the Done key. BKSP (backspace) deletes the previous digit.

National ISDN – enter your full 10-digit telephone number (including area code)

5ESS Custom ISDN – enter your 7-digit telephone number

ENTER PRIMARY PHONE #

785-1243 BKSP

24Tone Commander 6210/6220 User Manual

Image 27
Contents Page Contents Appendix a Ordering Isdn Service General Features IntroductionModels/Options Controls and Indicators OFF Page Dialing OperationPlacing a Call Selecting a Call AppearanceLast Number Redial Ringing Control Using DSS KeysAnswering a Call Call PreferenceBridging a Shared Call Appearance Displaying Call Appearance InformationHolding Calls Conferencing a New Call Transferring CallsConferencing Calls DSS TransferTerminating a Conference Using Network FeaturesConferencing a Held Call Dropping the Last PartyUsing the Call Log Delete Dial Time Back Viewing the Call LogCall Menu DIR LOG ID Select Call LOG Type Unans Answd OUTDialing a Call Log Entry Shortcut to the Unanswered Call LogDirectory PAGE1\ Using the Call DirectoryWhat is the Call Directory? Dialing from the Call DirectoryUsing the Speakerphone Placing and Answering CallsMuting the Microphone Using Voice Announce Enabling/DisablingReceiving Voice Announce Calls Headset Mode Operation Using a HeadsetAdjusting the Receive Volume Adjusting the Ringer VolumeSet the Termination Switches on the Telephone and NT1 InstallationOrdering Isdn Service 6210T/6220T InstallationExtended Point-to-Point Line and Power ConnectionsBasic Multipoint Short MultipointHandset/Headset Pin # Signal Wire ColorSet the Termination Switch on the Telephone 6210U/6220U InstallationVolt 6210U Power Supply 6220U Wall Mounting Rotating the BaseAttaching to a wall mount jack L1OK Configure the SetL3OK SWITCH=5ESS NI-X InitializationAutomatic Button Detection 5ESS Custom Isdn only No Parameter Download Press Setup to ConfigureFirmware Updates Using Local Inspect to Verify KeysPersonal Ringing Customize your PhoneLabel the Set Installation Options \ Spid Param Keys Installation OptionsInstallation Options Menu Setup Menu Instl Admin User PotsBksp Clear Spid EntryEnabling/Disabling Automatic Download Configuring KeysParameter Download Starting a DownloadBksp Orig Reserv CA/DN FA DSS SpdialUnused Call Appearance / Directory Number KeysAutomatic Call Appearance Selection 10=NETWORK FA#59 Call Bkspcall Feature Activator KeysBksp Clear Pause DSS KeysSpeed Dial Keys Bksp Clear Pause FABksp Pause FA Terminal MODE=CACH Ekts Cach Basic Terminal ModeVerify Password Bksp Installation PasswordInstallation Password SET Clear NEW Password BkspRemoving the Password Password ClearedWhat to do if you lose your password Reset to Factory Default Settings Reset ALL Setup OPTIONS? YES noALL Settings Cleared Select VA Keys GREEN=VA, RED=AVAILABLE Voice AnnounceVoice Announce Options Selecting CA/DN KeysBksp Clear ALL Selecting Incoming Directory NumbersALERTING=ANY Normal Dist Intcom PRI Selecting Alerting PatternsAutomatic MUTE=ON On OFF Automatic MutingAdministration Options \ Restart LOG Administration OptionsAdministration Options Menu Administration Options \ Inspct Vers Test DiagCall Appearance/Directory Number Key Local InspectLocal Inspect KeysDSS Key Feature Activator, Conference, Transfer, or Drop KeyOriginating DN? YES \ RESERVED=OUT/PRIORITY Originating DN? no RESERVED=NOT ReservedSpeed Dial Key Message Waiting IndicatorDirectory Numbers MESSAGE=NETWORK FI#63Hardware Version VersionVersion Serial H/W S/W Serial NumberMODEL6030X Button Expan Optional Equipment VersionDISPLAY/LED Test LCD RED Green OFF Display and LED IndicatorsTest Terminal Test Disply KeysPress Each KEY on Press Done to Exit Press Each KEY to Test Or GO OFF-HOOK to ExitKEY Test Passed Press ANY KEY to Exit 6030X Expansion ModuleDiagnostic Display RestartRESTART/CLEAR Call LOG? YES no Viewing the Error and Download Logs View LOG Entries Error Param ClearClearing Logs User Options User OptionsUser Options Menu User Options Clock Spdial DIR RingSetting the Time and Date Setting Up Speed Dial KeysBKSPAM/PM Smart Pauses Speed Dial ProgrammingSetting Up the Call Directory Select a Softkey PAGE1\Bksp Clear Move Number Deleting a Directory Entry Bksp Clear Pause NameMoving a Directory Entry Pick NEW Softkey PAGE1\Off-Hook Ringing Options Personal Ringing OptionsRinging Tone Ringing TONE=5 USE Keypad KeysRinging Control for Individual Call Appearances Call PREFERENCE=RINGING Ring Idle None Call Preference OptionsPreset Volume Levels Handset/Headset ConfigurationHandset/Headset Mode Voice MODE=HEADSET Hand Head VolumeAdjusting the Display Contrast Receive handset and headsetTransmit headset only Verify NEW Password Bksp Setting a Call Log PasswordCall LOG Password SET Clear Creating/Changing Your PasswordRemoving the Password Inoperable Telephone Recovery Procedures TroubleshootingWith full initialization, proceed to the following steps CA/DN trouble Check Fix Telephone Configuration TroubleshootingOrdering Manually Ordering Isdn ServiceSetup Wizard Where to Go for HelpNetwork Assignment Button # Recommended Button AssignmentsInstl Installation Options Setup Menu TreeAdmin Administration Options User User Options Pots 6002TA Analog Pots Port Options Tone Commander Product Warranty Warranty and ServiceSpecifications Parameter Default Value National Isdn 5ESS Custom Isdn Factory Default SettingsUL/FCC Statements Important Safety InstructionsPage FCC Requirements Page Page 13-102800 Rev. L