Sanyo POA-PN02C owner manual Chapter Installation

Page 15

Chapter 2

Installation

Describes how to install the network unit and software, and config- ure the network.

2

ENGLISH

PJ-NET ORGANIZER OWNER'S MANUAL [PLV-80/75 Series]

15

Image 15
Contents PJ-Net Organizer plus C PLV-80/75 Series POA-PN02CAddress ComplianceFederal Communication Commission Notice Model Numbers POA-PN02C Trade Name Sanyo Responsible partyEnglish Contents Use of Serial Port ContentsPage Chapter Web Management function +p.25 FeaturesTion Multi-control func Tion +p.58PDA restriction Operating environment of PJ-Net OrganizerPackage contains Before useHook and loop fastener small Safety ropePJ Camera Viewer software Camera mounting tool set Hook and loop fastener bigExpression/Abbreviation Use of this manualTrademarks Preparation Chapter Installation Function of the network unit p.17 Flow of installationInstallation and network configuration p.18-24 Set up is completeName and function of each part Mounting Installation and network configurationTighten two screws by using a coin etc Connector cover Screw coverConnection of LAN cable Confirmation of the network menu Network configurationConfigure the network Default network configuration is set as followsCompleting of installation Configuration for IP Address/ Sub net/ Gateway*1/DNS*2How to enter the numbers Fixing the network configurationFixing the Network PIN code Network PIN code settingDisplaying Network PIN code menu Entering the Network PIN codeHow to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorSelect a display mode and login Tion p.20. The default IP address isMain setting page in the Standard Mode display Display of main settingHow to use the setting Main setting page in the Light Mode displayExample of the Setting Radio button setting Type of the setting palletText box setting Pull-down menu settingUse of Battery Initial settingPJLink and password setting To 32 alphanumeric characters can be used for the passwordWhats PJLink? Date and time setting Auto settingManual setting Network configuration When using the e-mail functionMum Tor Mail settingSetting Smtp server and administrator address Menu and follow the below stepsRegistering and deleting E-mail addresses Option selection for sending alert mailLength of message should be less than 256 characters Examples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reachedCommunity Snmp settingEnter user name of the projector etc. optional Enter place of the projector optionalUp to 10 trap addresses can be registered Check and delete the trap addressTrap Item DescriptionTrap option Trap option settingChapter Controlling the Projector Power control and status check PJ statusPJ temp Status Description About projector conditionInput ControlsSystem Input source Image adjustmentMenu SoundPC adjustment Full Zoom Normal Natural wide True Setting up the projectorNatural wide, True There may not be available Table below Sets the image top/bottom and left/rightLamp Corres. Value Reset Setting procedureExecute button Save the controls and settings Store/free the settingsUp to 18 characters can be used for the Memo Load a control set Check the saved itemsTimer setting How to set the timerSet a day or date Select an event action Check the timer eventsChange the event mode Set an execute timeEvent Items Description Projector informationStatus Indication of the lamp statusControlling and setting the multi-projectors Multi-controlExample of multi control Start/stop the multi control Multi control settingConfirmation of registered projector Enter projector name or installed location etcWord None is displayed if not using the Memo func- tion Register the projectorChange the mode of the registered projector Mode OperationStatus Check & Change page in the light mode Setting all togetherControlling all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Equipment Control examplesExample Controlling AV equipment through networkPJ3 PJ2 PJ1 Use of telnet ControlPreparation When the word Hello is replied, login has been succeeded Control the projector with telnet Command FunctionChapter Appendix Examples of connection Peer-To-Peer connectionTo another network Entrance hall Gateway Router installed in the networkProxy setting Web browser settingActive Script/JavaScript enable Flash Player enableInternet Explorer ActiveX controls and plug-ins settingExamples OS/Browsers Windows XP ProfessionalFlash Player Add-on setting Using proxy serverNot using proxy server Netscape Navigator JavaScript SettingProxy setting Product specification Port specification Pin modular connector RJ-45Mini DIN-8pin connector Why doesn’t the setting page appear in my web browser? Projector setting Computer settingFollowing causes are possible. Please check them How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Can I develop a driver to control external serial equipment? Why am I not receiving E-mail alert messages?Can I update the firmware of the network unit What is the MAC address assigned to the network unit? What are the rules for IP address assignment?MAC address is indicated on the case back as the below Ifff