Sanyo POA-PN02C owner manual Why am I not receiving E-mail alert messages?

Page 85

Q&A

QWhy am I not receiving E-mail alert messages?

AMake sure that the registered E-mail address and SMTP server address are correct. If

the SMTP server is located in your LAN (Local Area network), the address should be set to the SMTP server in your LAN. The SMTP server located outside of your LAN may not be available for security reason. For further information please contact your network administrator (☞ p.34).

It may be required for the authentication depending on the SMTP server. This prod- uct does not support this kind of SMTP server.

Others

QCan I develop a driver to control external serial equipment?

AThis product does not provide any driver software. To control the external equip-

ment connected to the extra serial port, it should be required to clarify the com- mands and communication condition defined by each equipment. If they are clari- fied, it can be controlled by using the Telnet application installed on your computer. Please see item "Use of telnet" (☞ p.68).

QCan I control the projector by using the telnet application?

A Possible. Please refer to the item "Control the projector with telnet" (☞ p.70).

ENGLISH

PJ-NET ORGANIZER OWNER'S MANUAL [PLV-80/75 Series]

85

Image 85

Contents PJ-Net Organizer plus C PLV-80/75 Series POA-PN02CFederal Communication Commission Notice ComplianceModel Numbers POA-PN02C Trade Name Sanyo Responsible party AddressEnglish Contents Use of Serial Port ContentsPage Chapter Web Management function +p.25 FeaturesTion Multi-control func Tion +p.58PDA restriction Operating environment of PJ-Net OrganizerPackage contains Before usePJ Camera Viewer software Safety ropeCamera mounting tool set Hook and loop fastener big Hook and loop fastener smallUse of this manual Expression/AbbreviationTrademarks Preparation Chapter Installation Installation and network configuration p.18-24 Flow of installationSet up is complete Function of the network unit p.17Name and function of each part Tighten two screws by using a coin etc Installation and network configurationConnector cover Screw cover MountingConnection of LAN cable Configure the network Network configurationDefault network configuration is set as follows Confirmation of the network menuHow to enter the numbers Configuration for IP Address/ Sub net/ Gateway*1/DNS*2Fixing the network configuration Completing of installationDisplaying Network PIN code menu Network PIN code settingEntering the Network PIN code Fixing the Network PIN codeHow to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Select a display mode and login Login the setting page of the projectorTion p.20. The default IP address is Enter the IP addressMain setting page in the Standard Mode display Display of main settingMain setting page in the Light Mode display How to use the settingExample of the Setting Text box setting Type of the setting palletPull-down menu setting Radio button settingUse of Battery Initial settingTo 32 alphanumeric characters can be used for the password PJLink and password settingWhats PJLink? Auto setting Date and time settingManual setting When using the e-mail function Network configurationMum Setting Smtp server and administrator address Mail settingMenu and follow the below steps TorOption selection for sending alert mail Registering and deleting E-mail addressesLength of message should be less than 256 characters Examples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reachedEnter user name of the projector etc. optional Snmp settingEnter place of the projector optional CommunityTrap Check and delete the trap addressItem Description Up to 10 trap addresses can be registeredTrap option Trap option settingChapter Controlling the Projector PJ status Power control and status checkPJ temp Status Description About projector conditionInput ControlsSystem Input source Image adjustmentMenu SoundPC adjustment Natural wide, True There may not be available Setting up the projectorTable below Sets the image top/bottom and left/right Full Zoom Normal Natural wide TrueSetting procedure Lamp Corres. Value ResetExecute button Store/free the settings Save the controls and settingsUp to 18 characters can be used for the Memo Load a control set Check the saved itemsHow to set the timer Timer settingSet a day or date Change the event mode Check the timer eventsSet an execute time Select an event actionEvent Items Description Projector informationStatus Indication of the lamp statusMulti-control Controlling and setting the multi-projectorsExample of multi control Start/stop the multi control Multi control settingWord None is displayed if not using the Memo func- tion Enter projector name or installed location etcRegister the projector Confirmation of registered projectorMode Operation Change the mode of the registered projectorStatus Setting all together Check & Change page in the light modeControlling all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Example Control examplesControlling AV equipment through network EquipmentPJ3 PJ2 PJ1 Control Use of telnetPreparation When the word Hello is replied, login has been succeeded Control the projector with telnet Command FunctionChapter Appendix Peer-To-Peer connection Examples of connectionTo another network Entrance hall Gateway Router installed in the networkActive Script/JavaScript enable Web browser settingFlash Player enable Proxy settingExamples OS/Browsers ActiveX controls and plug-ins settingWindows XP Professional Internet ExplorerUsing proxy server Flash Player Add-on settingNot using proxy server Netscape Navigator JavaScript SettingProxy setting Product specification Pin modular connector RJ-45 Port specificationMini DIN-8pin connector Projector setting Computer setting Why doesn’t the setting page appear in my web browser?Following causes are possible. Please check them How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Can I develop a driver to control external serial equipment? Why am I not receiving E-mail alert messages?Can I update the firmware of the network unit What are the rules for IP address assignment? What is the MAC address assigned to the network unit?MAC address is indicated on the case back as the below Ifff