Sanyo POA-PN02C Installation and network configuration, Mounting, Connector cover Screw cover

Page 18

Chapter 2 Installation

[2] Installation and network configuration

Mounting

1 Disconnect the AC plug from the projector.

2 Remove the connector cover and screw covers (2 pieces) from the projector and insert plug on this product to the option connector.

Connector cover

18

Screw cover

3 Tighten two screws by using a coin etc.

!Caution

✐AC cord must be disconnected when mounting or removing this product otherwise it may dam- age the product.

✐Do not install multiple network units into a projector otherwise it may damage the product.

✐ Connect the AC cord after connecting the LAN cable and computer.

Image 18

Contents POA-PN02C PJ-Net Organizer plus C PLV-80/75 SeriesModel Numbers POA-PN02C Trade Name Sanyo Responsible party ComplianceFederal Communication Commission Notice AddressEnglish Contents Contents Use of Serial PortPage Chapter Features Web Management function +p.25Multi-control func Tion +p.58 TionOperating environment of PJ-Net Organizer PDA restrictionBefore use Package containsCamera mounting tool set Hook and loop fastener big Safety ropePJ Camera Viewer software Hook and loop fastener smallExpression/Abbreviation Use of this manualTrademarks Preparation Chapter Installation Set up is complete Flow of installationInstallation and network configuration p.18-24 Function of the network unit p.17Name and function of each part Connector cover Screw cover Installation and network configurationTighten two screws by using a coin etc MountingConnection of LAN cable Default network configuration is set as follows Network configurationConfigure the network Confirmation of the network menuFixing the network configuration Configuration for IP Address/ Sub net/ Gateway*1/DNS*2How to enter the numbers Completing of installationEntering the Network PIN code Network PIN code settingDisplaying Network PIN code menu Fixing the Network PIN codeHow to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Tion p.20. The default IP address is Login the setting page of the projectorSelect a display mode and login Enter the IP addressDisplay of main setting Main setting page in the Standard Mode displayHow to use the setting Main setting page in the Light Mode displayExample of the Setting Pull-down menu setting Type of the setting palletText box setting Radio button settingInitial setting Use of BatteryPJLink and password setting To 32 alphanumeric characters can be used for the passwordWhats PJLink? Date and time setting Auto settingManual setting Network configuration When using the e-mail functionMum Menu and follow the below steps Mail settingSetting Smtp server and administrator address TorRegistering and deleting E-mail addresses Option selection for sending alert mailLength of message should be less than 256 characters Examples Type and contents of alert mail When PJ lamp replacement time is reached When lamp corres. value reaches preselect use timeEnter place of the projector optional Snmp settingEnter user name of the projector etc. optional CommunityItem Description Check and delete the trap addressTrap Up to 10 trap addresses can be registeredTrap option setting Trap optionChapter Controlling the Projector Power control and status check PJ statusPJ temp About projector condition Status DescriptionControls InputSystem Image adjustment Input sourceSound MenuPC adjustment Table below Sets the image top/bottom and left/right Setting up the projectorNatural wide, True There may not be available Full Zoom Normal Natural wide TrueLamp Corres. Value Reset Setting procedureExecute button Save the controls and settings Store/free the settingsUp to 18 characters can be used for the Memo Check the saved items Load a control setTimer setting How to set the timerSet a day or date Set an execute time Check the timer eventsChange the event mode Select an event actionEvent Projector information Items DescriptionIndication of the lamp status StatusControlling and setting the multi-projectors Multi-controlExample of multi control Multi control setting Start/stop the multi controlRegister the projector Enter projector name or installed location etcWord None is displayed if not using the Memo func- tion Confirmation of registered projectorChange the mode of the registered projector Mode OperationStatus Check & Change page in the light mode Setting all togetherControlling all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Controlling AV equipment through network Control examplesExample EquipmentPJ3 PJ2 PJ1 Use of telnet ControlPreparation When the word Hello is replied, login has been succeeded Command Function Control the projector with telnetChapter Appendix Examples of connection Peer-To-Peer connectionTo another network Gateway Router installed in the network Entrance hallFlash Player enable Web browser settingActive Script/JavaScript enable Proxy settingWindows XP Professional ActiveX controls and plug-ins settingExamples OS/Browsers Internet ExplorerFlash Player Add-on setting Using proxy serverNot using proxy server JavaScript Setting Netscape NavigatorProxy setting Product specification Port specification Pin modular connector RJ-45Mini DIN-8pin connector Why doesn’t the setting page appear in my web browser? Projector setting Computer settingFollowing causes are possible. Please check them How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Why am I not receiving E-mail alert messages? Can I develop a driver to control external serial equipment?Can I update the firmware of the network unit What is the MAC address assigned to the network unit? What are the rules for IP address assignment?MAC address is indicated on the case back as the below Ifff