Sanyo POA-PN02C owner manual Control the projector with telnet, Command Function

Page 70

Chapter 5 Use of Serial Port

Control the projector with telnet

This product allows you to control the projector by using the telnet application. Normally, it is used for controlling the external equipment connected to the serial port but it also controls the projector by specifying the telnet port number 10000.

*To control the projector with telnet application is not depending on the serial port setting.

In the step 2 of the previous item "Control"(☞ p.68), enter port number "10000" after the IP address number.

> open 192.168.1.201 10000 [return]

* Use the IP address assigned to the pro- jector

After the communication is established, type the password (PIN code) and the command for controlling the projector and then press "Enter" key.

The table below shows the typical command lists for controlling the our projector and please consult your local dealer for further information of another commands.

Command list table

Command Function

C00	Power on
C02	Power off
C05	Selects input1
C06	Selects input2
C07	Selects input3
C09	Volume up
C0A	Volume down
C0B	Audio Mute on
C0C	Audio Mute off
C0F	Screen Normal size
C10	Screen Full size
C1C	Menu display on
C1D	menu display off
C23	Input2 (Video)
C24	Input2 (Y,Pb/Cb,Pr/Cr)
C25	Input2 (RGB)
C33	Input3 (Video)
C34	Input3 (S-Video)
C35	Input3 (Y,Pb/Cb,Pr/Cr)

70

Image 70

Contents POA-PN02C PJ-Net Organizer plus C PLV-80/75 SeriesModel Numbers POA-PN02C Trade Name Sanyo Responsible party ComplianceFederal Communication Commission Notice AddressEnglish Contents Contents Use of Serial PortPage Chapter Features Web Management function +p.25Multi-control func Tion +p.58 TionOperating environment of PJ-Net Organizer PDA restrictionBefore use Package containsCamera mounting tool set Hook and loop fastener big Safety ropePJ Camera Viewer software Hook and loop fastener smallUse of this manual Expression/AbbreviationTrademarks Preparation Chapter Installation Set up is complete Flow of installationInstallation and network configuration p.18-24 Function of the network unit p.17Name and function of each part Connector cover Screw cover Installation and network configurationTighten two screws by using a coin etc MountingConnection of LAN cable Default network configuration is set as follows Network configurationConfigure the network Confirmation of the network menuFixing the network configuration Configuration for IP Address/ Sub net/ Gateway*1/DNS*2How to enter the numbers Completing of installationEntering the Network PIN code Network PIN code settingDisplaying Network PIN code menu Fixing the Network PIN codeHow to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Tion p.20. The default IP address is Login the setting page of the projectorSelect a display mode and login Enter the IP addressDisplay of main setting Main setting page in the Standard Mode displayMain setting page in the Light Mode display How to use the settingExample of the Setting Pull-down menu setting Type of the setting palletText box setting Radio button settingInitial setting Use of BatteryTo 32 alphanumeric characters can be used for the password PJLink and password settingWhats PJLink? Auto setting Date and time settingManual setting When using the e-mail function Network configurationMum Menu and follow the below steps Mail settingSetting Smtp server and administrator address TorOption selection for sending alert mail Registering and deleting E-mail addressesLength of message should be less than 256 characters Examples Type and contents of alert mail When PJ lamp replacement time is reached When lamp corres. value reaches preselect use timeEnter place of the projector optional Snmp settingEnter user name of the projector etc. optional CommunityItem Description Check and delete the trap addressTrap Up to 10 trap addresses can be registeredTrap option setting Trap optionChapter Controlling the Projector PJ status Power control and status checkPJ temp About projector condition Status DescriptionControls InputSystem Image adjustment Input sourceSound MenuPC adjustment Table below Sets the image top/bottom and left/right Setting up the projectorNatural wide, True There may not be available Full Zoom Normal Natural wide TrueSetting procedure Lamp Corres. Value ResetExecute button Store/free the settings Save the controls and settingsUp to 18 characters can be used for the Memo Check the saved items Load a control setHow to set the timer Timer settingSet a day or date Set an execute time Check the timer eventsChange the event mode Select an event actionEvent Projector information Items DescriptionIndication of the lamp status StatusMulti-control Controlling and setting the multi-projectorsExample of multi control Multi control setting Start/stop the multi controlRegister the projector Enter projector name or installed location etcWord None is displayed if not using the Memo func- tion Confirmation of registered projectorMode Operation Change the mode of the registered projectorStatus Setting all together Check & Change page in the light modeControlling all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Controlling AV equipment through network Control examplesExample EquipmentPJ3 PJ2 PJ1 Control Use of telnetPreparation When the word Hello is replied, login has been succeeded Command Function Control the projector with telnetChapter Appendix Peer-To-Peer connection Examples of connectionTo another network Gateway Router installed in the network Entrance hallFlash Player enable Web browser settingActive Script/JavaScript enable Proxy settingWindows XP Professional ActiveX controls and plug-ins settingExamples OS/Browsers Internet ExplorerUsing proxy server Flash Player Add-on settingNot using proxy server JavaScript Setting Netscape NavigatorProxy setting Product specification Pin modular connector RJ-45 Port specificationMini DIN-8pin connector Projector setting Computer setting Why doesn’t the setting page appear in my web browser?Following causes are possible. Please check them How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Why am I not receiving E-mail alert messages? Can I develop a driver to control external serial equipment?Can I update the firmware of the network unit What are the rules for IP address assignment? What is the MAC address assigned to the network unit?MAC address is indicated on the case back as the below Ifff