Sanyo POA-PN02C owner manual About projector condition, Status Description

Page 43

Power control and status check

About projector condition

Status	Description

Normal	Projector is operating normally.
Power management under operation...	Power management is operating
Lamp failure	Lamp failure is occurring
Abnormal temperature	The temperature of the projector became too high
Cooling off due to abnormal temp	Projector detects abnormal temp. and is cooling down itself.
Power failure	Power failure has occurred inside the projector. Projector is turned
	off. Disconnect the AC cord and ask servicing to a qualified ser-
	vice personnel.
	If the power failure occurs on the projector, "Power failure" is
	indicated on the status column and the information icon appears
	on the power column as shown below. Click this icon to display
	further information of the power failure.
	Click this icon to display
	further information of
	the power failure.

When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control the projector through the network temporarily, execute "PJ lock suspend" command to unlock the security. "PJ lock suspend" is on setting sub menu [3] on Setting main menu. (+p.50)

ENGLISH

✐The projector cannot be turned on while the projector is on cooling down.

✐The web browser checks and updates the projector's condition every 30 seconds automatically.

PJ-NET ORGANIZER

OWNER'S MANUAL [PLV-80/75 Series]

43

Image 43

Contents PJ-Net Organizer plus C PLV-80/75 Series POA-PN02CAddress ComplianceFederal Communication Commission Notice Model Numbers POA-PN02C Trade Name Sanyo Responsible partyEnglish Contents Use of Serial Port ContentsPage Chapter Web Management function +p.25 FeaturesTion Multi-control func Tion +p.58PDA restriction Operating environment of PJ-Net OrganizerPackage contains Before useHook and loop fastener small Safety ropePJ Camera Viewer software Camera mounting tool set Hook and loop fastener bigUse of this manual Expression/AbbreviationTrademarks Preparation Chapter Installation Function of the network unit p.17 Flow of installationInstallation and network configuration p.18-24 Set up is completeName and function of each part Mounting Installation and network configurationTighten two screws by using a coin etc Connector cover Screw coverConnection of LAN cable Confirmation of the network menu Network configurationConfigure the network Default network configuration is set as followsCompleting of installation Configuration for IP Address/ Sub net/ Gateway*1/DNS*2How to enter the numbers Fixing the network configurationFixing the Network PIN code Network PIN code settingDisplaying Network PIN code menu Entering the Network PIN codeHow to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorSelect a display mode and login Tion p.20. The default IP address isMain setting page in the Standard Mode display Display of main settingMain setting page in the Light Mode display How to use the settingExample of the Setting Radio button setting Type of the setting palletText box setting Pull-down menu settingUse of Battery Initial settingTo 32 alphanumeric characters can be used for the password PJLink and password settingWhats PJLink? Auto setting Date and time settingManual setting When using the e-mail function Network configurationMum Tor Mail settingSetting Smtp server and administrator address Menu and follow the below stepsOption selection for sending alert mail Registering and deleting E-mail addressesLength of message should be less than 256 characters Examples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reachedCommunity Snmp settingEnter user name of the projector etc. optional Enter place of the projector optionalUp to 10 trap addresses can be registered Check and delete the trap addressTrap Item DescriptionTrap option Trap option settingChapter Controlling the Projector PJ status Power control and status checkPJ temp Status Description About projector conditionInput ControlsSystem Input source Image adjustmentMenu SoundPC adjustment Full Zoom Normal Natural wide True Setting up the projectorNatural wide, True There may not be available Table below Sets the image top/bottom and left/rightSetting procedure Lamp Corres. Value ResetExecute button Store/free the settings Save the controls and settingsUp to 18 characters can be used for the Memo Load a control set Check the saved itemsHow to set the timer Timer settingSet a day or date Select an event action Check the timer eventsChange the event mode Set an execute timeEvent Items Description Projector informationStatus Indication of the lamp statusMulti-control Controlling and setting the multi-projectorsExample of multi control Start/stop the multi control Multi control settingConfirmation of registered projector Enter projector name or installed location etcWord None is displayed if not using the Memo func- tion Register the projectorMode Operation Change the mode of the registered projectorStatus Setting all together Check & Change page in the light modeControlling all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Equipment Control examplesExample Controlling AV equipment through networkPJ3 PJ2 PJ1 Control Use of telnetPreparation When the word Hello is replied, login has been succeeded Control the projector with telnet Command FunctionChapter Appendix Peer-To-Peer connection Examples of connectionTo another network Entrance hall Gateway Router installed in the networkProxy setting Web browser settingActive Script/JavaScript enable Flash Player enableInternet Explorer ActiveX controls and plug-ins settingExamples OS/Browsers Windows XP ProfessionalUsing proxy server Flash Player Add-on settingNot using proxy server Netscape Navigator JavaScript SettingProxy setting Product specification Pin modular connector RJ-45 Port specificationMini DIN-8pin connector Projector setting Computer setting Why doesn’t the setting page appear in my web browser?Following causes are possible. Please check them How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Can I develop a driver to control external serial equipment? Why am I not receiving E-mail alert messages?Can I update the firmware of the network unit What are the rules for IP address assignment? What is the MAC address assigned to the network unit?MAC address is indicated on the case back as the below Ifff