Sanyo POA-PN02C Configuration for IP Address/ Sub net/ Gateway1/DNS2, How to enter the numbers

Page 21

Installation and network configuration

2Configuration for IP Address/ Sub net/ Gateway1/DNS2

Press SELECT button again. The following network setting pallet appears on the screen. Enter the specified network addresses.

The red frame moves sequentially left or right with 7 8 button.

The number up or down with d e button.

How to enter the numbers

There are 2 ways to enter the numbers, one is by using the point buttons (d e ) on the remote control or on the projector, the other is by using the screen 10-key pallet by which the numbers can be entered directory. For further information see "How to enter the numbers with the screen 10-key pallet" (☞ p.23).

3 Fixing the network configuration

After completing the entering of address, select "SET" and press SELECT button. The network unit starts re-booting and displays message "Please wait..." on the screen until the re-booting is complete. Do not disconnect the AC cord during this period.

Completing of installation

Now the installation is complete. The IP address of this projector is set to "192.168.1.201".

	Item	Description

	IP address	Sets IP address of the projector
	Sub net	Sets Subnet mask. Normally sets 255.255.255.0
	Gateway*1	Sets IP address of the default gateway (Router)
	DNS*2	Sets IP address of the DNS server. Must be set when using the e-mail function
	✐ Refer to the projector's owner's manual for operation of the projector.
				ENGLISH
				ENGLISH

*1 In the network environments not using a Gateway or Router, the Gateway address should be set to [0.0.0.0]. *2 If you do not use the functions E-mail or DNS server, it is also set [0.0.0.0] for the DNS address.

PJ-NET ORGANIZER

OWNER'S MANUAL [PLV-80/75 Series]

21

Image 21

Contents PJ-Net Organizer plus C PLV-80/75 Series POA-PN02CFederal Communication Commission Notice ComplianceModel Numbers POA-PN02C Trade Name Sanyo Responsible party AddressEnglish Contents Use of Serial Port ContentsPage Chapter Web Management function +p.25 FeaturesTion Multi-control func Tion +p.58PDA restriction Operating environment of PJ-Net OrganizerPackage contains Before usePJ Camera Viewer software Safety ropeCamera mounting tool set Hook and loop fastener big Hook and loop fastener smallExpression/Abbreviation Use of this manualTrademarks Preparation Chapter Installation Installation and network configuration p.18-24 Flow of installationSet up is complete Function of the network unit p.17Name and function of each part Tighten two screws by using a coin etc Installation and network configurationConnector cover Screw cover MountingConnection of LAN cable Configure the network Network configurationDefault network configuration is set as follows Confirmation of the network menuHow to enter the numbers Configuration for IP Address/ Sub net/ Gateway*1/DNS*2Fixing the network configuration Completing of installationDisplaying Network PIN code menu Network PIN code settingEntering the Network PIN code Fixing the Network PIN codeHow to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Select a display mode and login Login the setting page of the projectorTion p.20. The default IP address is Enter the IP addressMain setting page in the Standard Mode display Display of main settingHow to use the setting Main setting page in the Light Mode displayExample of the Setting Text box setting Type of the setting palletPull-down menu setting Radio button settingUse of Battery Initial settingPJLink and password setting To 32 alphanumeric characters can be used for the passwordWhats PJLink? Date and time setting Auto settingManual setting Network configuration When using the e-mail functionMum Setting Smtp server and administrator address Mail settingMenu and follow the below steps TorRegistering and deleting E-mail addresses Option selection for sending alert mailLength of message should be less than 256 characters Examples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reachedEnter user name of the projector etc. optional Snmp settingEnter place of the projector optional CommunityTrap Check and delete the trap addressItem Description Up to 10 trap addresses can be registeredTrap option Trap option settingChapter Controlling the Projector Power control and status check PJ statusPJ temp Status Description About projector conditionInput ControlsSystem Input source Image adjustmentMenu SoundPC adjustment Natural wide, True There may not be available Setting up the projectorTable below Sets the image top/bottom and left/right Full Zoom Normal Natural wide TrueLamp Corres. Value Reset Setting procedureExecute button Save the controls and settings Store/free the settingsUp to 18 characters can be used for the Memo Load a control set Check the saved itemsTimer setting How to set the timerSet a day or date Change the event mode Check the timer eventsSet an execute time Select an event actionEvent Items Description Projector informationStatus Indication of the lamp statusControlling and setting the multi-projectors Multi-controlExample of multi control Start/stop the multi control Multi control settingWord None is displayed if not using the Memo func- tion Enter projector name or installed location etcRegister the projector Confirmation of registered projectorChange the mode of the registered projector Mode OperationStatus Check & Change page in the light mode Setting all togetherControlling all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Example Control examplesControlling AV equipment through network EquipmentPJ3 PJ2 PJ1 Use of telnet ControlPreparation When the word Hello is replied, login has been succeeded Control the projector with telnet Command FunctionChapter Appendix Examples of connection Peer-To-Peer connectionTo another network Entrance hall Gateway Router installed in the networkActive Script/JavaScript enable Web browser settingFlash Player enable Proxy settingExamples OS/Browsers ActiveX controls and plug-ins settingWindows XP Professional Internet ExplorerFlash Player Add-on setting Using proxy serverNot using proxy server Netscape Navigator JavaScript SettingProxy setting Product specification Port specification Pin modular connector RJ-45Mini DIN-8pin connector Why doesn’t the setting page appear in my web browser? Projector setting Computer settingFollowing causes are possible. Please check them How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Can I develop a driver to control external serial equipment? Why am I not receiving E-mail alert messages?Can I update the firmware of the network unit What is the MAC address assigned to the network unit? What are the rules for IP address assignment?MAC address is indicated on the case back as the below Ifff