Sanyo POA-PN02C owner manual How to enter the numbers with the screen 10-key pallet

Page 23

Installation and network configuration

How to enter the numbers with the screen 10-key pallet

1 Select a column with a red frame by using the point buttons 7 8 .

2 Press SELECT button. The screen 10-key pallet appears on the screen.

3 By using the point buttons (d e 7 8), select numbers 0 to 9 and press SELECT button. By repeating the above to enter the complete number on the column.

*To change the number in a column, select “C” and press SELECT button to clear the number in the column and then enter the number again.

4 After entering the number in the column, select a move key (7 8 e d) located on the lower part of the pallet by using the point buttons and press SELECT button repeatedly to move the red frame.

5 Repeat steps 3 to 4 for entering all the network address.

6 After finishing, select "Exit" and press SELECT button. The 10-key pallet disappears on the screen.

10-key pallet

Exit

ENGLISH

PJ-NET ORGANIZER OWNER'S MANUAL [PLV-80/75 Series]

Image 23

Contents PJ-Net Organizer plus C PLV-80/75 Series POA-PN02CAddress ComplianceFederal Communication Commission Notice Model Numbers POA-PN02C Trade Name Sanyo Responsible partyEnglish Contents Use of Serial Port ContentsPage Chapter Web Management function +p.25 FeaturesTion Multi-control func Tion +p.58PDA restriction Operating environment of PJ-Net OrganizerPackage contains Before useHook and loop fastener small Safety ropePJ Camera Viewer software Camera mounting tool set Hook and loop fastener bigTrademarks Expression/AbbreviationUse of this manual Preparation Chapter Installation Function of the network unit p.17 Flow of installationInstallation and network configuration p.18-24 Set up is completeName and function of each part Mounting Installation and network configurationTighten two screws by using a coin etc Connector cover Screw coverConnection of LAN cable Confirmation of the network menu Network configurationConfigure the network Default network configuration is set as followsCompleting of installation Configuration for IP Address/ Sub net/ Gateway*1/DNS*2How to enter the numbers Fixing the network configurationFixing the Network PIN code Network PIN code settingDisplaying Network PIN code menu Entering the Network PIN codeHow to enter the numbers with the screen 10-key pallet Installation Chapter Basic Setting and Operation Enter the IP address Login the setting page of the projectorSelect a display mode and login Tion p.20. The default IP address isMain setting page in the Standard Mode display Display of main settingExample of the Setting How to use the settingMain setting page in the Light Mode display Radio button setting Type of the setting palletText box setting Pull-down menu settingUse of Battery Initial settingWhats PJLink? PJLink and password settingTo 32 alphanumeric characters can be used for the password Manual setting Date and time settingAuto setting Mum Network configurationWhen using the e-mail function Tor Mail settingSetting Smtp server and administrator address Menu and follow the below stepsLength of message should be less than 256 characters Registering and deleting E-mail addressesOption selection for sending alert mail Examples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reachedCommunity Snmp settingEnter user name of the projector etc. optional Enter place of the projector optionalUp to 10 trap addresses can be registered Check and delete the trap addressTrap Item DescriptionTrap option Trap option settingChapter Controlling the Projector PJ temp Power control and status checkPJ status Status Description About projector conditionInput ControlsSystem Input source Image adjustmentMenu SoundPC adjustment Full Zoom Normal Natural wide True Setting up the projectorNatural wide, True There may not be available Table below Sets the image top/bottom and left/rightExecute button Lamp Corres. Value ResetSetting procedure Up to 18 characters can be used for the Memo Save the controls and settingsStore/free the settings Load a control set Check the saved itemsSet a day or date Timer settingHow to set the timer Select an event action Check the timer eventsChange the event mode Set an execute timeEvent Items Description Projector informationStatus Indication of the lamp statusExample of multi control Controlling and setting the multi-projectorsMulti-control Start/stop the multi control Multi control settingConfirmation of registered projector Enter projector name or installed location etcWord None is displayed if not using the Memo func- tion Register the projectorStatus Change the mode of the registered projectorMode Operation Controlling all together Check & Change page in the light modeSetting all together Chapter Use of Serial Port Serial port setting Setting examples for the serial control Equipment Control examplesExample Controlling AV equipment through networkPJ3 PJ2 PJ1 Preparation Use of telnetControl When the word Hello is replied, login has been succeeded Control the projector with telnet Command FunctionChapter Appendix To another network Examples of connectionPeer-To-Peer connection Entrance hall Gateway Router installed in the networkProxy setting Web browser settingActive Script/JavaScript enable Flash Player enableInternet Explorer ActiveX controls and plug-ins settingExamples OS/Browsers Windows XP ProfessionalNot using proxy server Flash Player Add-on settingUsing proxy server Netscape Navigator JavaScript SettingProxy setting Product specification Mini DIN-8pin connector Port specificationPin modular connector RJ-45 Following causes are possible. Please check them Why doesn’t the setting page appear in my web browser?Projector setting Computer setting How can I restrict access from the computer What should I do when I forget the password? You can register up to 10 addresses Can I develop a driver to control external serial equipment? Why am I not receiving E-mail alert messages?Can I update the firmware of the network unit MAC address is indicated on the case back as the below What is the MAC address assigned to the network unit?What are the rules for IP address assignment? Ifff