VTech ia5877, ia5876, ia5874 user manual FCC, Acta and IC Regulations, FCC Part

Page 46

FCC, ACTA and IC Regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules.. These requirements are intended to provide reasonable protection against harmful interference in a residential installation.. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.. However, there is no guarantee that interference will not occur in a particular installation.. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

*Reorient or relocate the receiving antenna..

*Increase the separation between the equipment and receiver..

*Connect the equipment into an outlet on a circuit different from that to which the receiver is connected..

*Consult the dealer or an experienced radio/TV technician for help..

Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product.. This product has been tested and found to comply with the FCC criteria.. The handset may be safely held against the ear of the user.. The base unit shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more.. If you choose to use a clipping device, please make sure to only use the supplied VTech belt clip..

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA).. The label on the back or bottom of this equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA.. A compliant telephone cord and modular plug is provided with this product.. It is designed to be connected to a compatible modular jack that is also compliant.. An RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines.. See Installation Instructions in the user’s manual..

The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called.. The REN for this product is encoded as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information, please contact your local telephone company..

This equipment may not be used with Party Lines.. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected.. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents.. For repair procedures, follow the instructions outlined under the Limited Warranty..

If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service.. The telephone company is required to notify you before interrupting service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone company is required to notify you if such changes are planned..

If this product is equipped with a corded or cordless handset, it is hearing aid compatible..

If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:

www.vtechphones.com

ADDITIONAL INFO 45

Additional Information

Page 45 Page 47
Image 46
Page 45 Page 47
Contents User’s Manual Table of Contents Table of Contents Need HELP? VTech toll free 1-800-595-9511 In Canada dialBefore You Begin Parts Check ListInstall Handset Battery InstallationChoose Location Connect Power and Telephone Line Cords U g t h e Adapter into Electrical outlet.. IfDesk/Table Installation Wall MountingSet the Dial Mode Charge the Handset BatterySet Language Mode Check for Dial ToneHandset Ringer Style/Battery Save Set Handset Date and TimeBelt clip optional If you subscribe to DSL serviceTo remove Telephone Operation Handset OperationTemporary Tone Dialing Base OperationMessage Waiting Clear Message Waiting Alert When you have a message waiting, the handset will displayCall Transfer Operating Range Headset JackWalk back into range, periodically pressing OFF Display Screen Messages Speed Dialing Store a Number/Name in Speed DialEdit a Number/Name Stored in Speed Dial Press select to save the edited informationDial a Speed Dial Number Delete a Number/Name Stored in Speed DialReassign Locations in Speed Dial Store a Number/Name in the Directory Telephone DirectoryEdit a Number/Name Stored in the Directory Delete a Number/Name Stored in the Directory Move a Number/Name to the Speed Dial Memory Dial a Number from the DirectoryCaller ID About Call History Caller ID Review Call HistoryStore a Call History Record in the Directory Delete Records from Call HistoryDial a Displayed Number Locate the record in call history that you want to dialDialing sequence Code + number number only 1+ number.. See the noteSide margin for more information on changing Press select, then press Or until ProgramAnswering System Operation At the Base Audible IndicatorsSetting the clock About AnnouncementsTo review your announcement at any time System on or off Confirm feature settingsRecord Your Announcement To delete your announcementSetting Up Your Answering System Feature SummaryOff Listen to, Save & Delete MessagesTurn the base ringer on or off Choose how many times the phone willPress to play messages.. Press again to stop playback Call Screening/InterceptRecord a Memo To stop recording, press the PLAY/STOP againWindow Display When Connect with the Answering System Answering System Operation Remote AccessRemote Access Commands Voice MenuTurn system on Again to turn the system back onCode, then press 0 to turn the answering system on Battery Care and performance BatteriesTroubleshooting Problem SuggestionNoise Off in this troubleshooting guideComputers, kitchen appliances and other cordless phones For further instruction ServiceManual If you subscribe to DSLWhen I’m near Or weak signal evenGet noise, static Ring when I receive Manual Call My handset does notMy calls fade or cut Out while I’m usingUp to one minute for the handset and base to reset My handsetMy Caller ID isn’t Maintenance Warranty StatementHow do you get warranty service? Important Safety Instructions FCC, Acta and IC Regulations FCC PartRbrc Seal Industry CanadaTechnical Specifications Receive Frequency Base 5863..80 5872..5 MHzIndex IndexIndex 91-000499-070-000
Top Page Image Contents