Motorola CLP1010, CLP1040, CLP series manual Charging Status LEDs, Charger LED Indicator

Page 23

Note: If the radio is ON while charging, it will take longer to fully charge.

5.Insert the radio (with battery installed) into the charging pocket.

Note: The radio will fit in the charger with the holster attached when placed face down in the tray. The battery can be charged by itself using the slot on the flat surface of the charging pocket.

Charging Status LEDs

On the drop-in charger, the radio charging pocket has an LED Charger.

On the MUC, each of the 6 charging pockets has an LED. The LEDs are grouped into pairs to show which charging pockets are paired. The LED is red when the battery is charging. It turns to green once the battery is fully charged.

Note: This Multi Unit Charger allows you to clone up to 2 radios (2 Source radios and 2 Target radios). For more details, refer to “Radio Cloning” Section on page 21.

•For part number details, refer to the“Accessories” Section on page 41.

Charger LED Indicator

Status	LED Status					Comments

Charging	Steady					The charger is
	Red					currently charging.
	Indication

Charge	Steady					Battery is fully
Complete	Green					charged.
	Indication

Battery	Blinking					Battery was faulty
Battery	Blinking					Battery was faulty
Fault (*)	Red					when inserted.
Fault (*)	Red					when inserted.

Note: The LED is red when the battery is charging. It turns to green once the battery is fully charged.

Note: (*) Re-seating the battery pack will likely correct this issue.

BATTERY AND CHARGER FEATURES

15

Image 23

Contents Page Disclaimer Document CopyrightsContents Radio Cloning Batteries and Chargers Safety InformationRadio Frequency Code Charts Motorola Limited Warranty Programming the Radio Through CPSComputer Software Copyrights Product Safety and RF Exposure Compliance Radio Frequency RF Exposure Safety StandardsFCC Licensing Information FCC Licensing Information Introduction Radio Overview Getting Started Install the Battery Connecting an Audio Accessory Turning the Radio On and Off Adjusting the VolumeInstalling and Removing the Swivel Belt Clip Holster Talk Range Transmitting and ReceivingHOW to Step Operation with Menu SettingsSelecting a Channel Default Channel Settings for CPSFor CLP1040 multi-channel models Sending Call Tone enabled through CPSMonitoring a Channel For CLP1010 single-channel modelsBattery Life Battery and Charger FeaturesBattery Features About the Li-Ion BatteryBattery Recycling and Disposal Power Supply, Adapter and Drop-in Tray Charger Removing the Lithium-Ion Li-Ion BatteryEstimated Charging Time Charging the BatteryCharging a Standalone Battery Charging with the Drop-in Tray Single Unit Charger SUC Charging Status LEDs Charger LED IndicatorLED Checking Battery StatusBatteries Chargers Safety Information Operational Safety Guidelines Programming the Radio Programming the Radio Through CPSRadio Programming Overview Downloading the Customer Programming Software CPSFactory Default Settings Cloning Instructions Cloning Radio SettingsRadio Cloning Radio Cloning What to do if cloning fails Cloning the Radio through a Multi-Unit Charger Programming the RPX through a Single Unit Charger CLP Repeater Capability Working with RPXProgramming the RPX through a Multi-Unit Charger CLP Repeater Capability Working with RPXSymptom Try this TroubleshootingCan either reduce obstructions or increase power 13 and Charger LED Indicator Section on Cannot activate VOX VOX feature might be OFF If the portable is submerged in water USE and CareCLP UHF Frequencies Radio Frequency and Code ChartsRadiofrequency CCTSS/DPL Interference Eliminator Codes DPL Products and Accessories Motorola Limited Warranty for the United StatesWhat Does this Warranty Cover? Exclusions WHO is COVERED? What WE will do to Correct Warranty ProblemsHOW to Obtain Warranty Service or Other INFORMATION? SoftwareRetain Your Original Proof of Purchase Software Copyright NoticeExport LAW Assurances Patent NoticeChargers AccessoriesCarry Accessories BatteriesAccessories Page 68012000044