Motorola Programming CLP Series Radios: CLP1010 and CLP1040 Guide
Page 28

PROGRAMMING THE RADIO THROUGH CPS

2.Make sure the radio is turned ON.

3.Once the radio is connected, open the CPS and select “Read” on the toolbar to get the radio profile. The CPS allows the user to change settings, such as General, Audio, Menu, Channels, Scan List, as well as select frequencies, PL/DPL codes on each channel.

4.After you change the settings, press “Write” on the toolbar to save the settings.

For more information on the Computer Programming Software, please refer to Help menu on the CPS.

Note: (*) CPS Programming Cable (P/N HKKN4025) is an accessory sold separately. Please contact your Motorola Point of Purchase for more information.

Factory Default Settings

Your radio is programmed at the factory to the following settings:

CLP1010 1W UHF 1 CH Radios Default Settings - BRUS

Channel

Frequency

Frequency

Code

Band

Value

width

#

#

Setting

(Hz)

(kHz)

 

 

 

 

 

1

2

464.5500

67

12.5

 

 

 

 

 

CLP1040 1W UHF 4 CH Radios Default Settings - BRUS

Channel

Frequency

Frequency

Code

Band

Value

width

#

#

Settings

(Hz)

(kHz)

 

 

 

 

 

1

2

464.5500

67

12.5

 

 

 

 

 

2

8

467.9250

67

12.5

 

 

 

 

 

3

5

467.8500

67

12.5

 

 

 

 

 

4

6

467.8750

67

12.5

 

 

 

 

 

20

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Page Document Copyrights DisclaimerContents Batteries and Chargers Safety Information Radio Frequency Code Charts Motorola Limited WarrantyProgramming the Radio Through CPS Radio CloningComputer Software Copyrights Radio Frequency RF Exposure Safety Standards Product Safety and RF Exposure ComplianceFCC Licensing Information FCC Licensing Information Introduction Radio Overview Getting Started Install the Battery Connecting an Audio Accessory Installing and Removing the Swivel Belt Clip Holster Adjusting the VolumeTurning the Radio On and Off Transmitting and Receiving Talk RangeOperation with Menu Settings HOW to StepDefault Channel Settings for CPS Selecting a ChannelSending Call Tone enabled through CPS Monitoring a ChannelFor CLP1010 single-channel models For CLP1040 multi-channel modelsBattery and Charger Features Battery FeaturesAbout the Li-Ion Battery Battery LifeBattery Recycling and Disposal Removing the Lithium-Ion Li-Ion Battery Power Supply, Adapter and Drop-in Tray ChargerCharging a Standalone Battery Charging the BatteryEstimated Charging Time Charging with the Drop-in Tray Single Unit Charger SUC Charger LED Indicator Charging Status LEDsChecking Battery Status LEDBatteries Chargers Safety Information Operational Safety Guidelines Programming the Radio Through CPS Radio Programming OverviewDownloading the Customer Programming Software CPS Programming the RadioFactory Default Settings Radio Cloning Cloning Radio SettingsCloning Instructions Radio Cloning What to do if cloning fails Cloning the Radio through a Multi-Unit Charger CLP Repeater Capability Working with RPX Programming the RPX through a Single Unit ChargerCLP Repeater Capability Working with RPX Programming the RPX through a Multi-Unit ChargerTroubleshooting Symptom Try thisCan either reduce obstructions or increase power 13 and Charger LED Indicator Section on Cannot activate VOX VOX feature might be OFF USE and Care If the portable is submerged in waterRadio Frequency and Code Charts CLP UHF FrequenciesRadiofrequency CCTSS/DPL Interference Eliminator Codes DPL What Does this Warranty Cover? Motorola Limited Warranty for the United StatesProducts and Accessories Exclusions What WE will do to Correct Warranty Problems HOW to Obtain Warranty Service or Other INFORMATION?Software WHO is COVERED?Software Copyright Notice Retain Your Original Proof of PurchasePatent Notice Export LAW AssurancesAccessories Carry AccessoriesBatteries ChargersAccessories Page 68012000044
Top Page Image Contents