Nortel Networks BM450 manual LAN port LED locations, Status Description

Page 21

Chapter 3 Hardware Troubleshooting 21

LAN port LEDs

Each LAN port on the main unit and expansion unit has two LEDs. These LEDs indicate the status of the connection for that LAN port. The figure LAN port LED locations on page 21 shows the location of these LEDs on the main unit.

Figure 1 LAN port LED locations

LAN port

LAN port LEDs

LAN port

The table LAN port and expansion port LED indicators on page 21 describes the possible LED states for the LAN ports LEDs.

Table 2 LAN port and expansion port LED indicators

LED

Status

Description

 

 

 

Yellow (left

On

The LAN port is operating at 10 Mb/s.

LED)

 

 

 

 

 

 

Green (right

On

The LAN port is operating at 100 Mb/s.

LED)

 

 

Both LEDs

Off

No connection.

 

 

 

Any LED

Flashing

The LAN port is sending or receiving network data. The frequency of the flashes

 

 

increases with increased traffic.

 

 

 

Media bay module LEDs (expansion units only)

The two media bay module (MBM) LEDs on an expansion unit show the power and status of the

MBM. The figure MBM LEDs on page 22 shows the location of the (Power) and (Status) LEDs on an MBM. The power and status LEDs are in the same location on all MBMs.

BCM450 Troubleshooting Guide

Image 21
Contents BCM450 Troubleshooting Guide Copyright 2008 Nortel Networks, All Rights Reserved Task List BCM450 Troubleshooting GuideNN40160-700 Task ListContents Contents Chapter Advanced TroubleshootingChapter Understanding system messages Chapter Contacting Technical Support Purpose IntroductionAudience OrganizationIntroduction AcronymsList of acronyms Acronym DescriptionIntroduction List of acronyms Symbols and conventions used in this guide Related publications Introduction NN40160-700 Proper installation and routine maintenance Initial TroubleshootingNetwork configuration NavigationInitial Troubleshooting Device configuration informationNormal behavior on your network Logical connectionsInitial Troubleshooting Initial Troubleshooting NN40160-700 Troubleshooting the BCM450 hardware Hardware TroubleshootingCheck the power source Check LED indicatorsSystem status LEDs states and descriptions Hardware TroubleshootingStatus Description LAN port LED locationsMBM LED descriptions Power Status DescriptionStatus Descriptions DTM LED functionsCheck the wiring connections To verify the keycodes using Element ManagerVerify the keycodes Restart or shut down the system To verify the keycodes using TelsetReset functions To restart the systemFunction Description Impact Power on self test Hardware reset functionsViewing the Post log file Example Bootloader.log file with no errors Testing basic hardware functionalityTo test the main unit To troubleshoot the main unitTo test the expansion unit To troubleshoot the expansion unit Testing an MBMDetermining why an MBM does not appear in Element Manager Troubleshooting the FEMTo determine why the ATA 2 does not function To determine why there is no dial tone at the ATA2 To check the ATA2 wiringReset to factory settings Reset levels Monitoring the boot process To perform a Level 1 reset configuration resetTo perform a Level 2 reset software reset Hardware Troubleshooting Boot process with failed or missing memory Verify the software version Software TroubleshootingVerify the keycodes Check the programming of lines and phonesCheck line programming Software TroubleshootingTo check line programming Trunk/Line dataSoftware Troubleshooting Trunk/Line Data main panel Sheet 2 Properties Software Troubleshooting Trunk/Line Data main panel Sheet 3Trunk mode Properties line settings Sheet 1Dia l mode Line must be equipped with disconnect supervision fromSoftware Troubleshooting Properties line settings Sheet 2 SignalingPreferences Auto privacy Preferences details fields for lines Sheet 1Answer mode Restrictions RestrictionsTo restore data from an archive Restoring system dataAssigned DNs Select Components to Restore panel opens To restore the factory configurationVerify the software inventory Obtaining software updatesViewing the inventory of BCM450 software To view the BCM450 software inventoryTo obtain updates from the Nortel Technical Support Web Software Troubleshooting NN40160-700 Advanced Troubleshooting Troubleshooting exampleExample 1 Cannot dial out from an analog trunk Advanced Troubleshooting Example 2 Cannot dial out from a SIP or H323 VoIP trunk Advanced Troubleshooting Advanced Troubleshooting Advanced Troubleshooting Advanced Troubleshooting Example 3 IP set is not registering with the BCM450 Troubleshooting example 3b Troubleshooting example 3aAdvanced Troubleshooting Example 5 Cannot dial out from digital trunk Troubleshooting example Advanced Troubleshooting Advanced Troubleshooting Advanced Troubleshooting Advanced Troubleshooting Troubleshooting example Select Configuration Resources Telephony Resources System is not processing calls Recovery treesStart-up profile fails Recovery treesStart-up profile fails Cannot access BCM450 through Element ManagerCannot access BCM450 through Element Manager NN40160-700 BCM450 shuts down unexpectedly Unexpected shutdown BCM450 Troubleshooting GuideRecovery trees NN40160-700 Downloading Software Application User Administrator User ApplicationsDownloading software from the BCM450 webpage Applications available on BCM450 webDownloading Software Applications available on BCM450 web To download software from the BCM450 webpageDownloading Software Downloading software from the Nortel web siteDownloading Software NN40160-700 Troubleshooting Tools Service ManagementStatus and Metrics Accessing the CLI Command Line InterfaceTroubleshooting Tools UtilitiesAccessing the CLI through a serial connection Accessing the CLI through the OAM portUsing the Configuration CLI Using the Maintenance CLI Understanding system messages Alarms, logs, and trapsReporting for dropped calls To set Release ReasonsUnderstanding system messages Release reasons Knowledge and Solution Engine Useful Troubleshooting LinksUsing the Knowledge and Solution Engine Partner BulletinsUseful Troubleshooting Links To use the Knowledge and Solution EngineBackup, restore, and reset operations Frequently Asked QuestionsTo perform a backup How do I back up the database?How do I restore the BCM450 from a previous backup? To restore data from the BCM450Frequently Asked Questions Completing a warm or cold reset Password protectionHow do I recover a lost password for the BCM450? Recovering a lost passwordFault management How do I view Alarms? Can I acknowledge and clear them?To view an alarm Using the Element Manager to transfer log files To acknowledge an alarmSystem and status information How do I capture the logs from the BCM450?Using the BCM450 Web Page to transfer log files Capturing the current configuration How do I capture the current BCM450 configuration?Viewing the system health How do I find the BCM450 system health?How do I show specific process states? Viewing specific process statesVerify the current software revision Connectivity problemsHow do find the BCM450 System ID and Serial Number? Viewing the system ID and serial numberWhat are the default IP addresses of the BCM450 ports? What is an Ethernet loop, and how do I avoid creating one?IP addresses Can I modify the IP address of the OAM port?Frequently Asked Questions Frequently Asked Questions NN40160-700 Gathering critical information Contacting Technical SupportGetting help over the phone from a Nortel Solutions Center Getting Help from the Nortel Web siteContacting Technical Support Getting help through a Nortel distributor or reseller Contacting Technical Support NN40160-700