NEC R1000 manual Only the Xen Axis system can be saved as Xen IPK Basic

Page 11

Enhancement Guide to Migrating from Xen Axis/Master to Xen IPK R1000

5.From the Communications menu, select Download and click Start to download the database from the Xen Axis/Master system.

6.When the download is finished, select Save As from the File menu and enter a file name.

When the system is to be saved as Xen IPK Basic, confirm that Save As type is Xen IPK Basic (R1000) (*.rdf), and click Save.

When the system is to be saved as Xen IPK Expanded, confirm that Save As type is Xen IPK Expanded (R1000) (*.rdf) and click Save.

N Only the Xen Axis system can be saved as Xen IPK Basic.

September 2003

Doc. No. 8283 - Release 1.0

Direct Download from the Installed Xen System

Chapter 1 – 3

Image 11

Contents

Xen IPK This page Intentionally Left Blank Preface & Disclaimer Preface & Disclaimer Important Note About this Upgrade Procedure September Table of Contents 13-05 11-2-0413-00 13-04Chapter Xen IPK R1000 Upgrade Procedure for Xen Axis/ MasterChapter Direct Download from the Installed Xen System Only the Xen Axis system can be saved as Xen IPK Basic Chapter Direct Download from the Installed Xen System Upgrade Type Comments Chapter Direct Download from the Installed Xen System Click Hardware Upload When Upload is complete, click Close Chapter Direct Download from the Installed Xen System C T I O N September Only the Xen Axis system can be saved as Xen IPK Basic Upgrade Type Comments September September September For MIFM-U Software Verification for Mifm -U ETU For PRT1-U ETU Software Verification Adding AN Earth Connection B64-U23 KSU Hardware Description and Specifications for Xen IPK ChapterB64-U23 KSU Cpui -U ETU DescriptionInstallation SW3-1 Description Switch SettingsSW1-1 SW1-2 Description SW1-3 DescriptionDescription Flashing Off Replacing Memory BackupLED Indications Description Basic Port Expanded PKU 192-UA Port Key UnitESIB8-U ETU MDF ConnectionsESIE8-U ETU Pin Assignments MJ1 Pin Signal Signal Name Pin ColourMJ2 Pin Signal Signal Name Pin Colour This page Intentionally Left Blank Required Components Features and Specifications For Xen IPKAttendant Transfer Terminal Type¶+BTT Feature Feature Name NumberGeneral Shortcut KeyCall Arrival CAR Keys Restrictions Basic Port Expanded Feature Feature Name Number Call Appearance CAP Keys46/47 001 To return a call to the name/number displayed on the LCD Caller ID IncomingTo display a stored Caller ID Caller ID Indication Manual OperationScrolling Caller ID with Return Call General September Caller ID Indication disappears Mobile Pay Phone Out of Area Private Data Error Related Features ListShortcut Key Line Key Order Memory AttendantSystem Data Name Function Block Optional Components Dterm Series i Multiline TerminalsD-19Specifications Refer to individual feature for detailsGeneral Other TerminalButton Units Feature Name Number DTU-type Multiline Terminal MigrationD-20 September To change the LCD contrast for Multiline Display Terminals Electronic Volume ControlTo change the off-hook ringing volume To set the speaker volume To change the station ringing volumeTo set the handset receiver volume 46/47 049 Related Feature List Guide to Feature ProgrammingExternal Zone Paging Meet-Me E-6 To originate using a Multiline TerminalTo answer using a Multiline Terminal To answer using a Single Line Telephones To originate using a Single Line Telephones46/47 074 ~ 081 Full Duplex Handsfree To use the HFU-UA using an DTU--type Multiline Terminal¶+BTM HFU Selection Not applicable Data Assignment ISDN-BRI Trunk ConnectionsGeneral Xen IPK Expanded Order System Data Name CO Line ServiceOrder Memory System Data Name Function Calling Party Number CPN ServiceISDN-PRI Trunk Connections Not applicable Data Assignment for ISDN-PRI Installation Data Assignments for Caller ID Calling Party Number CPN Data Assignment for CO Line ServicesData Assignment for did Line Services General Xen IPK Expanded Isdn PRI Installation System Data Name Function Did Line ServiceCalling Party Number CPN Presentation from Station Music on Hold Example Guide to Feature Programming Station Transfer Using a Multiline Terminal with a call in progressUsing a Single Line Telephone with a call in progress Direct Station Selection DSS Package Universal SlotsNot applicable PRT4 4 ports, 4 B channels z PRT8 8 ports, 8 B channels Maximum Capacities Station Interface Units Description IPT4-U ETU installed as a COI/COID4-U ETU ESI8 ETUs NO. Maximum NO.Other ETUs Gruide to Feature Programming Programming + BK SettingsGeneral Description DisplayRelated Programming Programming ProceduresPRI Channel Assignment + AN Settings+ AN PRT B Channel Outgoing Priority SelectionPRT B Channel-to-Trunk Group Assignment + BCT Trunk-to-MOH Trunk AssignmentMultiline Terminal Type Selection + BTM Programming Procedures50, Multiline Terminal Type Selection Draft 3 MOH or Ring Back Tone Selection 66, MOH or Ring Back Tone Selection Draft 3 + BTT LCD Line Key Name Assignment68, LCD Line Key Name Assignment Draft 3 + BS Card Interface Slot AssignmentCard Interface Slot Assignment Draft 3 Draft Card Interface Slot Assignment ACD+/CMS/FMS/VMS KSU Power-Based ETU Quantity LimitationsEXP KTU Card Interface Slot AssignmentMIF ACD Assignment This page Intentionally Left Blank