NEC R1000 manual 68, LCD Line Key Name Assignment Draft 3

Page 103

Xen IPK	Programming

	LK Assign	Default	Note

	NON (not assigned)	All Blank

	CO Outside Lines	CO^xx	xx=Port 01~64

	Call Forward – Busy/No Answer	CFB

	Call Forward – All Calls	CFA

	Call Appearance Keys (CAP)	CAPxx-yy	xx=Block 00~47
	Call Appearance Keys (CAP)	CAPxx-yy	yy=Key 01~24
			yy=Key 01~24

	Programmable One-Touch Keys	FA xx	xx=key 01~24

	Trunk Group	TKGP^xx	xx=Trunk Group 01~32

	Route Advance Group	ADV^xx	xx=Group 01~16

	SIE including CAR	SIE^xxx	xxx=Port No. 01~99, AO~CO

	Microphone	MIC

	Headset On/Off Key	HSET

	Scroll Key for Caller ID indication	SCROLL

	Do Not Disturb On/Off	DND

	Log On/Off	LOG

	BGM On/Off	BGM

	Intercom Key	ICM

September 2003

Doc. No.: 8283 - Release 1.0

4 - 68, LCD Line Key – Name Assignment

DRAFT 3 Chapter 4 – 95

Image 103

Contents

Xen IPK This page Intentionally Left Blank Preface & Disclaimer Preface & Disclaimer Important Note About this Upgrade Procedure September Table of Contents 13-05 11-2-0413-00 13-04Chapter Xen IPK R1000 Upgrade Procedure for Xen Axis/ MasterChapter Direct Download from the Installed Xen System Only the Xen Axis system can be saved as Xen IPK Basic Chapter Direct Download from the Installed Xen System Upgrade Type Comments Chapter Direct Download from the Installed Xen System Click Hardware Upload When Upload is complete, click Close Chapter Direct Download from the Installed Xen System C T I O N September Only the Xen Axis system can be saved as Xen IPK Basic Upgrade Type Comments September September September For MIFM-U Software Verification for Mifm -U ETU For PRT1-U ETU Software Verification Adding AN Earth Connection B64-U23 KSU Hardware Description and Specifications for Xen IPK ChapterB64-U23 KSU Cpui -U ETU DescriptionInstallation SW3-1 Description Switch SettingsSW1-1 SW1-2 Description SW1-3 DescriptionLED Indications Replacing Memory BackupDescription Flashing Off Description Basic Port Expanded PKU 192-UA Port Key UnitESIB8-U ETU MDF ConnectionsESIE8-U ETU Pin Assignments MJ1 Pin Signal Signal Name Pin ColourMJ2 Pin Signal Signal Name Pin Colour This page Intentionally Left Blank Required Components Features and Specifications For Xen IPKAttendant Transfer Terminal Type¶+BTT Feature Feature Name NumberGeneral Shortcut KeyCall Arrival CAR Keys Restrictions 46/47 001 Feature Feature Name Number Call Appearance CAP KeysBasic Port Expanded To display a stored Caller ID Caller ID IncomingTo return a call to the name/number displayed on the LCD Caller ID Indication Manual OperationScrolling Caller ID with Return Call General September Caller ID Indication disappears Mobile Pay Phone Out of Area Private Data Error Related Features ListSystem Data Name Function Block Order Memory AttendantShortcut Key Line Key Optional Components Dterm Series i Multiline TerminalsD-19Specifications Refer to individual feature for detailsGeneral Button Units TerminalOther Feature Name Number DTU-type Multiline Terminal MigrationD-20 September To change the off-hook ringing volume Electronic Volume ControlTo change the LCD contrast for Multiline Display Terminals To set the handset receiver volume To change the station ringing volumeTo set the speaker volume 46/47 049 Related Feature List Guide to Feature ProgrammingTo answer using a Multiline Terminal To originate using a Multiline TerminalExternal Zone Paging Meet-Me E-6 To answer using a Single Line Telephones To originate using a Single Line Telephones46/47 074 ~ 081 Full Duplex Handsfree To use the HFU-UA using an DTU--type Multiline Terminal¶+BTM HFU Selection Not applicable Data Assignment ISDN-BRI Trunk ConnectionsGeneral Xen IPK Expanded Order System Data Name CO Line ServiceOrder Memory System Data Name Function Calling Party Number CPN ServiceISDN-PRI Trunk Connections Not applicable Data Assignment for ISDN-PRI Installation Data Assignment for did Line Services Data Assignment for CO Line ServicesData Assignments for Caller ID Calling Party Number CPN General Xen IPK Expanded Isdn PRI Installation System Data Name Function Did Line ServiceCalling Party Number CPN Presentation from Station Music on Hold Example Guide to Feature Programming Using a Single Line Telephone with a call in progress Using a Multiline Terminal with a call in progressStation Transfer Direct Station Selection DSS Not applicable Universal SlotsPackage PRT4 4 ports, 4 B channels z PRT8 8 ports, 8 B channels Maximum Capacities Station Interface Units Description IPT4-U ETU installed as a COI/COID4-U ETU Other ETUs NO. Maximum NO.ESI8 ETUs Gruide to Feature Programming Programming + BK SettingsGeneral Description DisplayRelated Programming Programming ProceduresPRI Channel Assignment + AN Settings+ AN PRT B Channel Outgoing Priority SelectionPRT B Channel-to-Trunk Group Assignment + BCT Trunk-to-MOH Trunk AssignmentMultiline Terminal Type Selection + BTM Programming Procedures 50, Multiline Terminal Type Selection Draft 3 MOH or Ring Back Tone Selection 66, MOH or Ring Back Tone Selection Draft 3 + BTT LCD Line Key Name Assignment68, LCD Line Key Name Assignment Draft 3 + BS Card Interface Slot AssignmentCard Interface Slot Assignment Draft 3 Draft Card Interface Slot Assignment ACD+/CMS/FMS/VMS KSU Power-Based ETU Quantity LimitationsEXP KTU Card Interface Slot AssignmentMIF ACD Assignment This page Intentionally Left Blank