NEC R1000 manual Preface & Disclaimer

Page 4

September 2003	NEC Business Solutions Ltd

NEC shall not be liable for any direct, indirect, consequential or incidental damages about the use of this equipment, manual or any related materials.

The information in this technical manual is advisory in nature and is subject to change. NEC may make improvements and changes in the products described in this manual without notice. Changes will be periodically made to the information in the new editions.

Efforts have been made to ensure that the contents of this manual are correct. Should you find any error, NEC welcomes your comments to improve our communications, please contact NEC on 1800 036 136.

Contents of this manual are subject to change without prior notice at the discretion of NEC Business Solutions Ltd.

This document has been prepared for the use of employees and customers of NEC Business Solutions Ltd and may not be reproduced without the prior, written approval of NEC Business Solutions Ltd.

Copyright 2003

NEC Business Solutions Ltd

635 Ferntree Gully Road

Glen Waverley Vic 3150

September 2003

Doc. No. 8283 - Release 1.0

ii	Preface & Disclaimer

Image 4

Contents

Xen IPK This page Intentionally Left Blank Preface & Disclaimer Preface & Disclaimer Important Note About this Upgrade Procedure September Table of Contents 11-2-04 13-0013-04 13-05Xen IPK R1000 Upgrade Procedure for Xen Axis/ Master ChapterChapter Direct Download from the Installed Xen System Only the Xen Axis system can be saved as Xen IPK Basic Chapter Direct Download from the Installed Xen System Upgrade Type Comments Chapter Direct Download from the Installed Xen System Click Hardware Upload When Upload is complete, click Close Chapter Direct Download from the Installed Xen System C T I O N September Only the Xen Axis system can be saved as Xen IPK Basic Upgrade Type Comments September September September For MIFM-U Software Verification for Mifm -U ETU For PRT1-U ETU Software Verification Adding AN Earth Connection Hardware Description and Specifications for Xen IPK Chapter B64-U23 KSUCpui -U ETU Description B64-U23 KSUInstallation Switch Settings SW1-1 SW1-2 DescriptionSW1-3 Description SW3-1 DescriptionLED Indications Replacing Memory BackupDescription Flashing Off PKU 192-UA Port Key Unit Description Basic Port ExpandedESIB8-U ETU Connections MDFESIE8-U ETU MJ1 Pin Signal Signal Name Pin Colour Pin AssignmentsMJ2 Pin Signal Signal Name Pin Colour This page Intentionally Left Blank Features and Specifications For Xen IPK Attendant TransferTerminal Type Required ComponentsFeature Feature Name Number GeneralShortcut Key ¶+BTTCall Arrival CAR Keys Restrictions 46/47 001 Feature Feature Name Number Call Appearance CAP KeysBasic Port Expanded To display a stored Caller ID Caller ID IncomingTo return a call to the name/number displayed on the LCD Manual Operation Caller ID IndicationScrolling Caller ID with Return Call General September Caller ID Indication disappears Related Features List Mobile Pay Phone Out of Area Private Data ErrorSystem Data Name Function Block Order Memory AttendantShortcut Key Line Key Dterm Series i Multiline TerminalsD-19 Optional ComponentsRefer to individual feature for details SpecificationsGeneral Button Units TerminalOther Feature Name Number DTU-type Multiline Terminal MigrationD-20 September To change the off-hook ringing volume Electronic Volume ControlTo change the LCD contrast for Multiline Display Terminals To set the handset receiver volume To change the station ringing volumeTo set the speaker volume Related Feature List Guide to Feature Programming 46/47 049To answer using a Multiline Terminal To originate using a Multiline TerminalExternal Zone Paging Meet-Me E-6 To originate using a Single Line Telephones To answer using a Single Line Telephones46/47 074 ~ 081 To use the HFU-UA using an DTU--type Multiline Terminal Full Duplex Handsfree¶+BTM HFU Selection ISDN-BRI Trunk Connections Not applicable Data AssignmentGeneral Xen IPK Expanded CO Line Service Order System Data NameCalling Party Number CPN Service Order Memory System Data Name FunctionISDN-PRI Trunk Connections Not applicable Data Assignment for ISDN-PRI Installation Data Assignment for did Line Services Data Assignment for CO Line ServicesData Assignments for Caller ID Calling Party Number CPN General Xen IPK Expanded Isdn PRI Installation Did Line Service System Data Name FunctionCalling Party Number CPN Presentation from Station Music on Hold Example Guide to Feature Programming Using a Single Line Telephone with a call in progress Using a Multiline Terminal with a call in progressStation Transfer Direct Station Selection DSS Not applicable Universal SlotsPackage PRT4 4 ports, 4 B channels z PRT8 8 ports, 8 B channels Maximum Capacities Station Interface Units Description IPT4-U ETU installed as a COI/COID4-U ETU Other ETUs NO. Maximum NO.ESI8 ETUs Gruide to Feature Programming Programming Settings General DescriptionDisplay + BKProgramming Procedures Related Programming+ AN Settings PRI Channel AssignmentPRT B Channel Outgoing Priority Selection + ANPRT B Channel-to-Trunk Group Assignment Trunk-to-MOH Trunk Assignment + BCT+ BTM Programming Procedures Multiline Terminal Type Selection50, Multiline Terminal Type Selection Draft 3 MOH or Ring Back Tone Selection 66, MOH or Ring Back Tone Selection Draft 3 LCD Line Key Name Assignment + BTT68, LCD Line Key Name Assignment Draft 3 Card Interface Slot Assignment + BSCard Interface Slot Assignment Draft 3 Draft Card Interface Slot Assignment KSU Power-Based ETU Quantity Limitations ACD+/CMS/FMS/VMSCard Interface Slot Assignment EXP KTUMIF ACD Assignment This page Intentionally Left Blank