NEC manual Xen IPK R1000 Upgrade Procedure for Xen Axis/ Master, Chapter

Page 9

Xen IPK R1000 Upgrade Procedure for Xen Axis/ Master

Chapter 1

S E C T I O N 1

MIGRATION FROM XEN AXIS/MASTER

S E C T I O N 2

DIRECT DOWNLOAD

FROM THE INSTALLED

XEN SYSTEM

September 2003

Doc. No. 8283 - Release 1.0

Use the following instructions to migrate from an existing Xen Axis/Master system to a Xen IPK R1000 system.

The Xen IPK Maintenance Administration Terminal (MAT) software must be used to perform this upgrade. The MIFM-U( ) ETU is required for PC Programming and must be installed.

Two methods to access the database from the existing system are explained below:

Direct download from the installed system

Import the Xen Axis/Master database saved using a previous version of the Xen Axis/Master MAT.

1.Verify that the battery is connected to CN4 on Xen Master CPUB( )- U( ) or Xen Axis MBD-U( ) Unit.

2.Confirm and record the following settings:

Answer Preset

Automated Attendant/DISA mode Automatic Trunk-to-Trunk Transfer mode Automatic Trunk-to-Trunk Transfer Outgoing Trunk Background Music

Call Forward – All Calls, Busy, No Answer, Busy/No Answer, Off- Premise/Split

Callback Messages Customized Message Display Day/Night Mode (System and Tenant) Do Not Disturb

MIC Settings

Timed Alarm

Migration from Xen Axis/Master

Chapter 1 – 1

Image 9

Contents

Xen IPK This page Intentionally Left Blank Preface & Disclaimer Preface & Disclaimer Important Note About this Upgrade Procedure September Table of Contents 13-00 11-2-0413-04 13-05Chapter Xen IPK R1000 Upgrade Procedure for Xen Axis/ MasterChapter Direct Download from the Installed Xen System Only the Xen Axis system can be saved as Xen IPK Basic Chapter Direct Download from the Installed Xen System Upgrade Type Comments Chapter Direct Download from the Installed Xen System Click Hardware Upload When Upload is complete, click Close Chapter Direct Download from the Installed Xen System C T I O N September Only the Xen Axis system can be saved as Xen IPK Basic Upgrade Type Comments September September September For MIFM-U Software Verification for Mifm -U ETU For PRT1-U ETU Software Verification Adding AN Earth Connection B64-U23 KSU Hardware Description and Specifications for Xen IPK ChapterB64-U23 KSU Cpui -U ETU DescriptionInstallation SW1-1 SW1-2 Description Switch SettingsSW1-3 Description SW3-1 DescriptionReplacing Memory Backup LED IndicationsDescription Flashing Off Description Basic Port Expanded PKU 192-UA Port Key UnitESIB8-U ETU MDF ConnectionsESIE8-U ETU Pin Assignments MJ1 Pin Signal Signal Name Pin ColourMJ2 Pin Signal Signal Name Pin Colour This page Intentionally Left Blank Attendant Transfer Features and Specifications For Xen IPKTerminal Type Required ComponentsGeneral Feature Feature Name NumberShortcut Key ¶+BTTCall Arrival CAR Keys Restrictions Feature Feature Name Number Call Appearance CAP Keys 46/47 001Basic Port Expanded Caller ID Incoming To display a stored Caller IDTo return a call to the name/number displayed on the LCD Caller ID Indication Manual OperationScrolling Caller ID with Return Call General September Caller ID Indication disappears Mobile Pay Phone Out of Area Private Data Error Related Features ListOrder Memory Attendant System Data Name Function BlockShortcut Key Line Key Optional Components Dterm Series i Multiline TerminalsD-19Specifications Refer to individual feature for detailsGeneral Terminal Button UnitsOther Feature Name Number DTU-type Multiline Terminal MigrationD-20 September Electronic Volume Control To change the off-hook ringing volumeTo change the LCD contrast for Multiline Display Terminals To change the station ringing volume To set the handset receiver volumeTo set the speaker volume 46/47 049 Related Feature List Guide to Feature ProgrammingTo originate using a Multiline Terminal To answer using a Multiline TerminalExternal Zone Paging Meet-Me E-6 To answer using a Single Line Telephones To originate using a Single Line Telephones46/47 074 ~ 081 Full Duplex Handsfree To use the HFU-UA using an DTU--type Multiline Terminal¶+BTM HFU Selection Not applicable Data Assignment ISDN-BRI Trunk ConnectionsGeneral Xen IPK Expanded Order System Data Name CO Line ServiceOrder Memory System Data Name Function Calling Party Number CPN ServiceISDN-PRI Trunk Connections Not applicable Data Assignment for ISDN-PRI Installation Data Assignment for CO Line Services Data Assignment for did Line ServicesData Assignments for Caller ID Calling Party Number CPN General Xen IPK Expanded Isdn PRI Installation System Data Name Function Did Line ServiceCalling Party Number CPN Presentation from Station Music on Hold Example Guide to Feature Programming Using a Multiline Terminal with a call in progress Using a Single Line Telephone with a call in progressStation Transfer Direct Station Selection DSS Universal Slots Not applicablePackage PRT4 4 ports, 4 B channels z PRT8 8 ports, 8 B channels Maximum Capacities Station Interface Units Description IPT4-U ETU installed as a COI/COID4-U ETU NO. Maximum NO. Other ETUsESI8 ETUs Gruide to Feature Programming Programming General Description SettingsDisplay + BKRelated Programming Programming ProceduresPRI Channel Assignment + AN Settings+ AN PRT B Channel Outgoing Priority SelectionPRT B Channel-to-Trunk Group Assignment + BCT Trunk-to-MOH Trunk AssignmentMultiline Terminal Type Selection + BTM Programming Procedures50, Multiline Terminal Type Selection Draft 3 MOH or Ring Back Tone Selection 66, MOH or Ring Back Tone Selection Draft 3 + BTT LCD Line Key Name Assignment68, LCD Line Key Name Assignment Draft 3 + BS Card Interface Slot AssignmentCard Interface Slot Assignment Draft 3 Draft Card Interface Slot Assignment ACD+/CMS/FMS/VMS KSU Power-Based ETU Quantity LimitationsEXP KTU Card Interface Slot AssignmentMIF ACD Assignment This page Intentionally Left Blank