SkyLink am-100 manual Part 2 Learn signal from Control Panel to Control Module

Page 16

INSTALLATION

For outdoor monitoring, please refer to page 30 to program the motion sensor to Alert Zone.

You may now close the battery cover and re-insert the screw.

Mount the ball-head joint on the wall with screws provided. Slide the back of the sensor into the ball-head joint. The mounting angle can be adjusted.

Testing

Walk test should be performed after the motion sensor is mounted. Walk in the detected area, if motion is detected, a red light inside the sensor will glow. If the red light does not glow, motion has not been detected and you may need to re-position the sensor. Ensure you walk test all the locations that you would like the motion sensor to cover.

HOME AUTOMATION

Control Module [1] is represented by zone LED 1

®

This row :

Buttons for

Learning Control Module

Part 2 Learn signal from Control Panel to Control Module

Note:

-Perform the walk test after you have inserted the battery for more than 1 minute.

-Before performing the walk test, the sensor should not detect any motion.

-After motion is detected once, the sensor will not be triggered unless no motion is detected for 20 seconds. Therefore, wait for at least 20 seconds during walk testing between 2 activations.

DETECTING AREA: (Unit = meter)

14

55°

1.2M

55°

 

12

 

 

11°

 

 

 

10

 

 

 

8

 

 

 

6

22°

27°

22°

 

 

4

 

 

 

2

 

 

 

M

 

 

 

 

12°

 

 

 

 

 

 

 

 

 

 

 

 

SENSOR

 

 

 

 

 

 

 

 

 

 

 

 

 

0

1

2

3

4

5

6

7

8

9

10

11

12

13

Step

Keys

Function

Description

Note

1

Press and hold

Enter

 

LED on the Control Module

 

the learn button

Programming

 

will flash indicating it is in

 

on the Control

mode

 

learn mode.

 

Module until its

 

 

 

 

LED starts to

 

 

 

 

flash.

 

 

 

 

 

 

 

 

2

[6] to [0]

Transmit an ON

Refer to the

After [X] is entered, you

 

signal for the

chart below to

will hear [Device X On]

 

 

 

 

selected device

determine which

indicating you have trans-

 

 

from the Control

button [6] to [0]

mitted an ON signal for

 

 

Panel to the

to press.

device X, where X is the

Caution:

When installing the motion sensor, avoid placing it near heat or cold producing devices (i.e. A/C or furnace vents, fans, ovens, space heaters, etc). Air movement, especially caused by changes in temperature may trigger the Motion Sensor and cause false alarms. Please carefully test your Motion Sensor so that it will only be triggered by wanted movement.

You have now successfully installed and programmed the Control Panel and its sensors. Please follow the rest of the instructions for operations and advanced programming.

–14–

 

Control Module. You should

Control Module Location.

 

 

transmit the “ON”

The LED on the Control

 

 

command for the

Module should be off,

 

 

selected device.

indicating it has learned

 

 

 

the signal, you may now

 

 

 

release the learn button

 

 

 

and the LED will stay on

 

 

 

again.

 

 

 

 

 

 

 

 

CONTROL MODULE

TRANSMIT

 

 

LOCATION

BUTTON [X]

 

 

 

 

 

 

1

6

 

 

 

 

 

 

2

7

 

 

 

 

 

 

3

8

 

 

 

 

 

 

4

9

 

 

5

0

 

 

 

 

 

 

–39–

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Email support@skylinkhome.com Skylink GroupHome Smart Center Declaration of Conformity EMCPage Content FCC Information Consumer InformationSystem Configuration IntroductionAccessories Introduction Accessories Installation Installing the ConsoleTrouble Shooting SensorsFrench EnglishProgramming Passwords Changing PasswordsOrder to change the password, follow the procedures below Questions SolutionsHome Automation Phone Number ProgrammingTesting Phone Numbers Event TriggerInstalling Door / Window Sensors TestingMounting the Sensor This is not a Control MODULE, THEREFORE, should not beInstalling Motion Sensor Insert BatteryOperation Erase Control ModulesPart 2 Learn signal from Control Panel to Control Module Alert Mode Part 1 Learn signal from Control Module to Control PanelAlert Mode Examples OperationMute Learn Control ModulesSend back a confirmation to the control panel To indicate the light has been turned onAdvanced Programming Operation System StatusErase Sensors Arming the SystemEntering the premises Enter password within Advanced ProgrammingDisarming the system Learn Sensors ContinueDisarming a triggered control panel Learn SensorsDisarming under Duress Panic System FailureErase Keychain / Keypad Remotes Phone Line FailureLow Battery Learn Keychain / Keypad RemotesSensor Failure Control PanelTo enable alert zone feature, follow the instructions below Keychain RemoteAdvanced Programming Communication It is recommend to enable alert zone ifReceiving the Emergency Call To access the control panel away from home Calling in when you are away from homeTo enable auto mute feature, follow the instructions below Remote Operation by TelephoneRemote Phone Operations ExampleSystem Disarmed Alert Mode Beep / AlarmSystem Armed Alarm Mode
Related manuals
Manual 28 pages 6.36 Kb

am-100 specifications

The SkyLink AM-100 is an innovative satellite communication system designed to provide seamless connectivity in remote and challenging environments. This system caters to a diverse range of industries, including maritime, aviation, and disaster recovery, delivering reliable communication solutions even in the most isolated locations.

One of the standout features of the SkyLink AM-100 is its compact and lightweight design, making it easy to transport and deploy in various scenarios. Weighing less than 10 pounds, the unit allows users to establish a communication link in a matter of minutes. The system also boasts rugged construction, enabling it to withstand harsh environmental conditions and ensuring continuous operation in extreme temperatures, humidity, and dust.

The AM-100 leverages advanced satellite technologies that allow for high-speed data transmission. With a bandwidth capacity that supports voice, video, and data services, users can experience real-time communication capabilities that are critical for timely decision-making and action in emergencies or pivotal situations. The system can provide a data rate of up to 5 Mbps, ensuring that users can send and receive large files or stream video feeds without interruption.

Another key characteristic of the SkyLink AM-100 is its user-friendly interface. The system features an intuitive control panel and easily accessible connectivity ports, simplifying the setup process. Users can quickly adapt the system for various applications, whether for on-the-ground operations or aerial surveillance.

Additionally, the AM-100 is designed with multi-network support, enabling users to switch between different satellite networks for enhanced reliability. This flexibility is particularly beneficial in regions with varying network availability, ensuring continuous service and connectivity.

Security is also a major focus of the SkyLink AM-100 system. It incorporates advanced encryption protocols to protect sensitive data and communications, making it suitable for military and governmental operations.

In conclusion, the SkyLink AM-100 stands out with its robust features, including portability, high-speed data capabilities, ease of use, multi-network support, and strong security measures. It is an essential tool for professionals requiring reliable connectivity in remote locations, helping to bridge the communication gap in critical situations. Whether for disaster relief, on-site operations, or remote monitoring, the SkyLink AM-100 is poised to deliver exceptional performance and reliability.
Top Page Image Contents