SkyLink am-100 manual Remote Phone Operations, Example

Page 27

ADVANCED PROGRAMMING

Follow the procedures below to program the beep / alarm setting.

Step

Keys

Function

Description

Note

 

 

 

 

 

1

[PROG]

Enter Programming

Enter master

3 beeps for valid password.

 

[MPIN]

mode

password to

1 long beep for invalid

 

 

 

programming mode

password.

 

 

 

 

 

2

[5]

Select Beep /

 

After [5] is entered, some zone

Alarm Setting

 

LEDs will flash or stay on.

 

 

 

 

 

 

 

This indicates whether that

 

 

 

 

zone is set to beep or alarm.

 

 

 

 

 

3

Set to Beep:

Select which

Refer to the

If Alarm is set for that zone,

 

[1] to [5]

zone you would

diagram below to

that zone LED will be on. If

 

 

like to Beep or

select the appro-

Beep is set, the LED will

 

Set to Alarm:

Alarm.

priate setting.

flash. You are allowed to

 

 

 

make multiple changes before

 

[6] to [0].

 

 

 

 

 

terminating programming

 

 

 

 

 

 

 

 

mode.

 

 

 

 

 

4

[PROG] when

Terminate pro-

 

PROG LED will be off, and

 

finished.

gramming mode.

 

you will hear 3 beeps.

 

 

 

 

 

COMMUNICATION

Table 1: Remote Phone Operations

SYSTEM OPERATION

PHONE COMMAND

DESCRIPTION

 

 

 

Turn on device x

x+[*]

Turn devices on will hear [Device X On]. When the

[x] = 1 to 5

control module receives the on signal, it will turn on the

 

 

 

 

plugged in device, and send a confirmation back to the

 

 

control panel. You will then hear [Device On Accepted].

 

 

 

Turn off device x

x+[#]

Turn devices off will hear [Device X Off]. When the

x = [1 to 5]

control module receives the off signal, it will turn off the

 

 

 

plugged in device, and send a confirmation back to the

 

 

control panel. You will then hear [Device Off Accepted].

 

 

 

Check system status

[8]+[#]

You will hear system status announcement

 

 

 

Arm

[7]+[#]

You will hear [System Armed]

 

 

 

Disarm

[9]+[#]

You will hear [System Disarmed]

 

 

 

Disconnect

[0]+[#]

Phone line disconnect

 

 

 

 

BEEP

ALARM

®

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zone 1

Button [1]

Button [6]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zone 2

Button [2]

Button [7]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zone 3

Button [3]

Button [8]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zone 4

Button [4]

Button [9]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Zone 5

Button [5]

Button [0]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This row : Buttons for Beep

Zone LED : Flash

This row : Buttons for Alarm

Zone LED : ON

Example:

If you would like to change the setting for zone 5 from “Beep” to “Alarm”, simply press [0] at step 3.

This will change the zone 5 setting to “Alarm”.

–28–

–25–

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Skylink Group Email support@skylinkhome.comHome Smart Center EMC Declaration of ConformityPage FCC Information Consumer Information ContentIntroduction System ConfigurationAccessories Introduction Accessories Installing the Console InstallationEnglish Trouble ShootingSensors FrenchQuestions Solutions Programming PasswordsChanging Passwords Order to change the password, follow the procedures belowPhone Number Programming Home AutomationEvent Trigger Testing Phone NumbersThis is not a Control MODULE, THEREFORE, should not be Installing Door / Window SensorsTesting Mounting the SensorErase Control Modules Installing Motion SensorInsert Battery OperationPart 2 Learn signal from Control Panel to Control Module Operation Alert ModePart 1 Learn signal from Control Module to Control Panel Alert Mode ExamplesTo indicate the light has been turned on MuteLearn Control Modules Send back a confirmation to the control panelArming the System Advanced Programming OperationSystem Status Erase SensorsLearn Sensors Continue Entering the premises Enter password withinAdvanced Programming Disarming the systemLearn Sensors Disarming a triggered control panelDisarming under Duress Phone Line Failure PanicSystem Failure Erase Keychain / Keypad RemotesControl Panel Low BatteryLearn Keychain / Keypad Remotes Sensor FailureKeychain Remote To enable alert zone feature, follow the instructions belowIt is recommend to enable alert zone if Advanced Programming CommunicationReceiving the Emergency Call Remote Operation by Telephone To access the control panel away from homeCalling in when you are away from home To enable auto mute feature, follow the instructions belowExample Remote Phone OperationsBeep / Alarm System Disarmed Alert ModeSystem Armed Alarm Mode
Related manuals
Manual 28 pages 6.36 Kb

am-100 specifications

The SkyLink AM-100 is an innovative satellite communication system designed to provide seamless connectivity in remote and challenging environments. This system caters to a diverse range of industries, including maritime, aviation, and disaster recovery, delivering reliable communication solutions even in the most isolated locations.

One of the standout features of the SkyLink AM-100 is its compact and lightweight design, making it easy to transport and deploy in various scenarios. Weighing less than 10 pounds, the unit allows users to establish a communication link in a matter of minutes. The system also boasts rugged construction, enabling it to withstand harsh environmental conditions and ensuring continuous operation in extreme temperatures, humidity, and dust.

The AM-100 leverages advanced satellite technologies that allow for high-speed data transmission. With a bandwidth capacity that supports voice, video, and data services, users can experience real-time communication capabilities that are critical for timely decision-making and action in emergencies or pivotal situations. The system can provide a data rate of up to 5 Mbps, ensuring that users can send and receive large files or stream video feeds without interruption.

Another key characteristic of the SkyLink AM-100 is its user-friendly interface. The system features an intuitive control panel and easily accessible connectivity ports, simplifying the setup process. Users can quickly adapt the system for various applications, whether for on-the-ground operations or aerial surveillance.

Additionally, the AM-100 is designed with multi-network support, enabling users to switch between different satellite networks for enhanced reliability. This flexibility is particularly beneficial in regions with varying network availability, ensuring continuous service and connectivity.

Security is also a major focus of the SkyLink AM-100 system. It incorporates advanced encryption protocols to protect sensitive data and communications, making it suitable for military and governmental operations.

In conclusion, the SkyLink AM-100 stands out with its robust features, including portability, high-speed data capabilities, ease of use, multi-network support, and strong security measures. It is an essential tool for professionals requiring reliable connectivity in remote locations, helping to bridge the communication gap in critical situations. Whether for disaster relief, on-site operations, or remote monitoring, the SkyLink AM-100 is poised to deliver exceptional performance and reliability.
Top Page Image Contents