Crestron electronic DMTH4 Installing LecNet2 Software and USB Driver, First Time Installation

Page 10

DMTH4

Installing LecNet2™ Software and USB Driver

LecNet2™ is a Graphic User Interface (GUI) designed to allow easy setup and monitoring of DM components using Windows® 2000 or XP computer systems.

LecNet2™ includes the necessary Control Panels to configure and monitor all the DM series products plus the Venue Modular Receiver system.

Installing LecNet2™ Software

1.Use the computer system’s control panel to remove any previously installed versions of LecNet2™ software. (This will ensure you are using the latest release.)

2.Insert the LecNet2™ program disk supplied with your system into the computer system’s CD-ROM drive.

3.The CD should automatically start the installation procedure. If it doesn't, click "Start" on the WIndows Task Bar then click "Run..." Enter the Drive number followed by "Setup.exe" then click OK.

4.Follow the on-screen instructions to install the LecNet2 software.

Installing the LecNet2™ USB Driver

There are two methods of connecting a Windows®- based computer system to the DM component, either via a USB cable or an RS-232 cable. Although the USB port offers significantly increased speed and conve- nience over standard RS-232 links, it does require the installation of a LecNet2™ USB driver.

The LecNet2 USB driver is not part of the standard Windows® 2000 and XP driver libraries. As a result, connecting a computer system to a DM system for the first time is different than subsequent installations. There are a few minor differences between installing the LecNet2 USB drivers on a Windows 2000 versus a Windows XP system.

USB driver installation Windows XP

First Time Installation

When a LecNet2™ device is connected to the PC for the very first time, the Windows Found New Hardware Wizard automatically opens. Use the following proce- dure to install the LecNet2™ USB driver using the Wizard.

1.Place the LecNet2™ Installation Disk in the PC’s CD-ROM drive.

2.On the first page of the Wizard, select the option

Install from a list or specific location (Ad- vanced) and click Next> to continue.

3.Select "Search for the best driver in these locations", then check "Search removable media (floppy, CD-ROM...)" and click Next> to continue.

4.Windows searchs the CD for the driver and when it has found it, it is likely that a dialog will open warning you that the driver has not passed Win- dows Logo Testing, click Continue Anyway.

10

LECTROSONICS, INC.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents DMTH4 DMTH4 LECTROSONICS, INC Important Safety Instructions Table of Contents Introduction Unpacking the unitFront Panel Controls and FeaturesRear Panel Cables Hardware InstallationInstalling the DM system into a rack Audio ConnectionsProgrammable Inputs Audio Outputs AUX and CodecTelephone Line Jack Programmable OutputsCodec and TEL Remote Control Ports Expansion I/O portsInstalling the LecNet2 USB Driver Installing LecNet2 Software and USB DriverInstalling LecNet2 Software USB driver installation Windows XPInstallation of Additional Units or LecNet 2 devices USB Driver Installation Windows Initial Setup Basic System SetupControl System Interconnections Master/Slave Configuration Using the DMTH4 Control Panel to Change Master/Slave ModeInitial Setup Hints Example Teleconferencing Setup DMTH4Setting up the DM1624 Main Matrix Setting up the DMTH4 Main MatrixSetting up the DM1624 Expansion Matrix Setting up the DMTH4 Output Source Multiplexer Using the Touch Tone Pad Make a Telephone Call Using a Telephone SetMake a Telephone Call Using the Activity Tab Making a Phone CallUse the Type the number to dial box Use the Phone BookConnecting to the Codec Interface using the Activity Tab FCC Part 68 Compliance FCC Part 15 ComplianceInstallation Guide Rio Rancho, NM Limited ONE Year Warranty
Top Page Image Contents