NEC ND-70895 (E) Assign the system data written in LDM, Asydl SYS1 INDEX512, INDEX513

Page 32

INSTALLATION PROCEDURE

OAI Software Installation

STEP 6: Assign the system data written in LDM.

ASYDL SYS1
INDEX512:	FPC of the self-node

When OAI system is used through the Fusion Network, this data setting is necessary at each node in the network.

INDEX513:	01 Hex (LDM usage)
INDEX515~518 b0~b7:	IP address (Hex) for PBX over external LAN	Note 4
INDEX519~522 b0~b7:	Subnet Mask (Hex) for PBX over external LAN	Note 4
INDEX523~526 b0~b7:	Default Gateway Address for External LAN	Note 4
(This data is required when the Host is connected via gateway)
INDEX864 -	b0=1 (Built-in IP is provided)

When OAI system is used in the Fusion Network (OAI Terminal Anywhere) [available since the Series 7400 (Release 8)

software], assign “1” at the node that has the IP.

INDEX864 b1 :Output the system message (4-R) when TCP-IP is normally disconnected. 0/1=Effective/Ineffective

Note 4: If the MAT or SMDR has been connected with external LAN already, this data assignment is not necessary.

STEP 7: Check the station-to-station connection and confirm no fault status occurs or system messages are output (such as cable connection fault, LCD display fault, memory alarm fault, abnormal interrupt etc.).

STEP 8: Program the OAI office data. Also, program the Fusion data to make ACD service effective through Fusion network, if necessary.

STEP 9: Save the DM into the HDD by using MEM_HDD.

CHAPTER 3

ND-70895 (E)

Page 22

Revision 1.0

Image 32

Contents ND-70895 E Stock #Liability Disclaimer NEC America, IncNEAX2400 IMX Issue No NEAX2400 IMX OAI System ManualTable of Contents ND-70895 Etable of Contents Page iii Revision List of Figures List of Tables This page is for your notes General How to Follow the ManualConfiguration of this manual is shown in Table Introduction System Outline Explains the outline of the OAI systemSystem Outline Block Concept of MSF Concept of TMF Concept of ACF Concept of TCF Concept of NTF 11 Concept of RCF 13 Concept of ATF Join of Facilities and Application System Configuration Symbol Symbol Name Circuit Card Remarks Dual System Configuration of NEAX2400 IMX IMG 15 IP Dual System ConfigurationInterface with External Computer Circuit Card Interface ConditionsThis page is for your notes Installation Procedure Cable Connections with External Computer OAI Software Installation System DATA=OVERRIDE/LOADChange system data written in DM Asyd SYS1INDEX513 Assign the system data written in LDMAsydl SYS1 INDEX512 Upgrading OAI System from NEAX2400 ICS to NEAX2400 IMX This page is for your notes Commands This section explains the construction of each commandConfiguration of Commands for OAI System Configuration of Commands of the NEAX2400 IMX OAI SystemCommands This section explains the commands in used in the OAI SystemInterrelation among OAI System Commands Aadt Assignment of Announcement/Dictation Trunks TypeMsgt WaitDisconnect Timer = Impossible = Possible Announcement/Dictation Trunk Data Assignment TableAcno Assignment of Conversion Number Data AmnoLcno LrtdConversion Number Data Assignment Table Akyd Assignment of Key Data for Dterm Amno Assignment of Monitored Number MNONMI UCDMonitored Number Assignment Table Loac Aoac Assignment of OAI Access CodeKind OAI Access Code Data Assignment Table Aokc Assignment of OAI Key Code Related Commands List Up Lokc Kind = 1 OP-CODE = 128 ~ Kind = 2 OP-CODE = 192 ~OAI Key Code Data Assignment Table Operation Code Remarks Aspa Assignment of Specific Access Code Service Feature Index aSida OAI Dial Number Batch Transfer TMFAsyd Assignment of System Data MTC System Data Assign Table Equipped capacity of the Common Memory CM 1 ~ 4 MbyteCalled Number Display when forwarding to Attendant Console Calling and Intermediate Station Number indication = # key/* key No CPU Mounted Status of IP00/1Not mounted/Mounted System Data Assign Table HEX/ASCII Data BIT System Data Contents Dfln Display of Location Free Numbering LstnPstn RSCAsydn Assignment of System Data in NDM Asydn Asydl Assignment of System Data into Local DM LDM Example IP Address Example Subnet MaskDefault Gateway Address Office Data Design Procedure for Setting Basic Office Data for OAI System ASYD/ASYDLASYDL-SYS1 INDEX513 Hex LDM usageAkyd AokcAoac AnpdProcedure for Setting Office Data for OAI Services Using Conditions Abnormal Sequence SYS1 Index B6 1 OAI service is not availableAssignment Asyd System Data Call ID Notification Smfn for Isdn Functional Outline Isdn Caller’s Number Information ≤ n ≤ Text Mail Module TMMFacsimile Mail Module FMMAbnormal Sequence NEAX2400 IMX DLC TSW SYS1 Index TCP/IP Address Assignment from MAT Functional Outline SYS1 IndexName Display Functional Outline INDEX78 INDEX79INDEX241 Asyd SYS1 INDEX78Catching call from other internal line Called partyCcis B6 = 0 OAI Service is in service B6 = 1 OAI Service is not in serviceAsyd SYS1 Index B1 = 0 Name Display 8-digitOAI Fusion Assignment of System Data Data for OAI Fusion ASYDL/ASYDNINDEX533 FPC number of the node that has the standard VndmMultiple IPs Functional Outline III III PBX Example of Use of Facility on Fusion Network This page is for your notes Maintenance Maintenance System Fault Contents of Fault System MessagesSystem Message 4-R TCP/IP Link Failure 1. Print-out Format System Message 4-RTCP/IP Link Failure NEC ESD= MIS ACD System Message 26-VLAN Interface Error Report= OAI Fault Diagnosis Flow of Fault RepairDiagnosis from System Messages Repairing Procedure for TCP/IP Link Failure Message 4-R StartND-70895 Echapter Revision This page is for your notes