NEC ND-70895 (E) system manual Interrelation among OAI System Commands

Page 38

COMMANDS

Commands

3.2Outline of Commands for OAI System

The interrelation among the commands to be used in the OAI System is illustrated in Figure 4-2.

		NEAX2400 IMX			External Computer
			IP
		DLC/ELC
	AKYD	ASDT	ASYD	Command Name		: Commands for NEAX2400
	AOKC	ASDT	ASYD
	AOKC	AKYD	ARNP	ASYD	: Assignment of System Data
	AOAC	AKYD	ARNP	ASYD	: Assignment of System Data
	AOAC			ARNP	: Assignment of Reverse Numbering Plan Data
				ARNP	: Assignment of Reverse Numbering Plan Data
				ASDT	: Assignment of Station Data
				AKYD	: Assignment of DtermKey Data

Figure 4-2 Interrelation among OAI System Commands

AKYD: This command is used to assign the function key codes (For OAI: 34 ~ 47) to the function key positions of the Dterm.

AOKC : This command is used to assign the meaning of OAI key code assigned by AKYD command.

Note 1: Function key codes 34 ~ 47 respectively correspond to OAI key codes (1 ~ 14).

AOAC : This command is used to assign the access code/operation code for the designated facility.

This command is used only when the Facility Kind (F-KIND) has been set to “3” (Open Appli- cation Interface) by AOKC command.

Note 2: Parameters OAI Key Code (KEY-CODE), Facility Kind (F-KIND), and Operation Code (OP-CODE) are determined by the application software to be used at each office.

3.3 Items to Be Explained by Each Command

Each command is described by the following items.

	Command	: The name implies the command and its functions.
(1)	Functions	: This item outlines the command functions.
(2)	Precaution	: This item explains precaution for use of the command.
(3)	Parameters	: This item explains the meaning of the information (parameters) of the data of
		the command.

(4)Related Commands : This item specifies other command or commands pertaining to the same data, assignment/deletion/change/display/list up of the details of that specific data.

CHAPTER 4

ND-70895 (E)

Page 28

Revision 1.0

Image 38

Contents ND-70895 E Stock #Liability Disclaimer NEC America, IncNEAX2400 IMX Issue No NEAX2400 IMX OAI System ManualTable of Contents ND-70895 Etable of Contents Page iii Revision List of Figures List of Tables This page is for your notes General How to Follow the ManualConfiguration of this manual is shown in Table Introduction System Outline Explains the outline of the OAI systemSystem Outline Block Concept of MSF Concept of TMF Concept of ACF Concept of TCF Concept of NTF 11 Concept of RCF 13 Concept of ATF Join of Facilities and Application System Configuration Symbol Symbol Name Circuit Card Remarks Dual System Configuration of NEAX2400 IMX IMG 15 IP Dual System ConfigurationInterface with External Computer Circuit Card Interface ConditionsThis page is for your notes Installation Procedure Cable Connections with External Computer Change system data written in DM OAI Software InstallationSystem DATA=OVERRIDE/LOAD Asyd SYS1INDEX513 Assign the system data written in LDMAsydl SYS1 INDEX512 Upgrading OAI System from NEAX2400 ICS to NEAX2400 IMX This page is for your notes Commands This section explains the construction of each commandConfiguration of Commands for OAI System Configuration of Commands of the NEAX2400 IMX OAI SystemCommands This section explains the commands in used in the OAI SystemInterrelation among OAI System Commands Msgt Aadt Assignment of Announcement/Dictation TrunksType WaitDisconnect Timer = Impossible = Possible Announcement/Dictation Trunk Data Assignment TableLcno Acno Assignment of Conversion Number DataAmno LrtdConversion Number Data Assignment Table Akyd Assignment of Key Data for Dterm NMI Amno Assignment of Monitored NumberMNO UCDMonitored Number Assignment Table Loac Aoac Assignment of OAI Access CodeKind OAI Access Code Data Assignment Table Aokc Assignment of OAI Key Code Related Commands List Up Lokc Kind = 1 OP-CODE = 128 ~ Kind = 2 OP-CODE = 192 ~OAI Key Code Data Assignment Table Operation Code Remarks Sida Aspa Assignment of Specific Access CodeService Feature Index a OAI Dial Number Batch Transfer TMFAsyd Assignment of System Data MTC System Data Assign Table Equipped capacity of the Common Memory CM 1 ~ 4 MbyteCalled Number Display when forwarding to Attendant Console Calling and Intermediate Station Number indication = # key/* key No CPU Mounted Status of IP00/1Not mounted/Mounted System Data Assign Table HEX/ASCII Data BIT System Data Contents Pstn Dfln Display of Location Free NumberingLstn RSCAsydn Assignment of System Data in NDM Asydn Asydl Assignment of System Data into Local DM LDM Example IP Address Example Subnet MaskDefault Gateway Address Office Data Design ASYDL-SYS1 INDEX513 Procedure for Setting Basic Office Data for OAI SystemASYD/ASYDL Hex LDM usageAoac AkydAokc AnpdProcedure for Setting Office Data for OAI Services Using Conditions Abnormal Sequence SYS1 Index B6 1 OAI service is not availableAssignment Asyd System Data Call ID Notification Smfn for Isdn Functional Outline Isdn Caller’s Number Information ≤ n ≤ Facsimile Mail Module Text Mail ModuleTMM FMMAbnormal Sequence NEAX2400 IMX DLC TSW SYS1 Index TCP/IP Address Assignment from MAT Functional Outline SYS1 IndexName Display Functional Outline INDEX241 INDEX78INDEX79 Asyd SYS1 INDEX78Catching call from other internal line Called partyCcis Asyd SYS1 Index B6 = 0 OAI Service is in serviceB6 = 1 OAI Service is not in service B1 = 0 Name Display 8-digitOAI Fusion INDEX533 Assignment of System Data Data for OAI FusionASYDL/ASYDN FPC number of the node that has the standard VndmMultiple IPs Functional Outline III III PBX Example of Use of Facility on Fusion Network This page is for your notes Maintenance Maintenance System Fault Contents of Fault System MessagesTCP/IP Link Failure System Message 4-R TCP/IP Link Failure 1. Print-out FormatSystem Message 4-R NEC ESD= MIS ACD System Message 26-VLAN Interface Error Report= OAI Fault Diagnosis Flow of Fault RepairDiagnosis from System Messages Repairing Procedure for TCP/IP Link Failure Message 4-R StartND-70895 Echapter Revision This page is for your notes