NEC ND-70895 (E) system manual Using Conditions

Page 73

OFFICE DATA DESIGN

Procedure for Setting Office Data for OAI Services

3.1.2Using Conditions

1.Normal and abnormal operating sequences pertaining to the basic connection of the SCF are as described below.

[Normal Sequence]

 

 

 

Destination Terminal

Calling Terminal

NEAX2400

Computer (AP)

 

 

 

SCF Activated

 

 

Terminal Check

 

 

 

Return Result

 

 

Connection

 

<Zip tone>

<Zip tone>

 

 

(a)Upon receiving SCF start request from the AP, the NEAX2400 IMX judges the status (idle, busy, makebusy, etc.) of the designated calling terminal and destination terminal.

(b)If the calling terminal and the destination terminal are idle, the NEAX2400 IMX sends out Return Result to the AP, and places the calling terminal into an outgoing connection status and the destination terminal into ringing status.

These are the basic functions.

(c)When the destination terminal designated from the AP is a terminal in the NEAX2400 IMX and automatic answer is designated as the answer type, both the calling and destination terminals can be placed into speech status immediately from the status cited in (b) (After zip tone has been sent to both terminals, the terminals are placed into speech status.).

Note that this service function is valid only when the destination terminal is in line selection wait status and also automatic answer is designated as the answer type. In other words, if the destination terminal is in a status other than line selection wait status, the call is to be answered

manually. Further, this service function is valid only when the destination terminal is a station (Dterm: Voice) among the SCF Make Call designations. In other words, if the call destination

is a trunk, this service function does not work.

ND-70895 (E)CHAPTER 5

Page 63

Revision 1.0

Image 73
Contents Stock # ND-70895 ENEC America, Inc Liability DisclaimerNEAX2400 IMX Issue No OAI System Manual NEAX2400 IMXTable of Contents ND-70895 Etable of Contents Page iii Revision List of Figures List of Tables This page is for your notes Configuration of this manual is shown in Table How to Follow the ManualGeneral Introduction Explains the outline of the OAI system System OutlineSystem Outline Block Concept of MSF Concept of TMF Concept of ACF Concept of TCF Concept of NTF 11 Concept of RCF 13 Concept of ATF Join of Facilities and Application System Configuration Symbol Symbol Name Circuit Card Remarks 15 IP Dual System Configuration Dual System Configuration of NEAX2400 IMX IMGCircuit Card Interface Conditions Interface with External ComputerThis page is for your notes Installation Procedure Cable Connections with External Computer System DATA=OVERRIDE/LOAD OAI Software InstallationChange system data written in DM Asyd SYS1Asydl SYS1 INDEX512 Assign the system data written in LDMINDEX513 Upgrading OAI System from NEAX2400 ICS to NEAX2400 IMX This page is for your notes This section explains the construction of each command CommandsConfiguration of Commands of the NEAX2400 IMX OAI System Configuration of Commands for OAI SystemThis section explains the commands in used in the OAI System CommandsInterrelation among OAI System Commands Type Aadt Assignment of Announcement/Dictation TrunksMsgt WaitAnnouncement/Dictation Trunk Data Assignment Table Disconnect Timer = Impossible = PossibleAmno Acno Assignment of Conversion Number DataLcno LrtdConversion Number Data Assignment Table Akyd Assignment of Key Data for Dterm MNO Amno Assignment of Monitored NumberNMI UCDMonitored Number Assignment Table Kind Aoac Assignment of OAI Access CodeLoac OAI Access Code Data Assignment Table Aokc Assignment of OAI Key Code Kind = 1 OP-CODE = 128 ~ Kind = 2 OP-CODE = 192 ~ Related Commands List Up LokcOAI Key Code Data Assignment Table Operation Code Remarks Service Feature Index a Aspa Assignment of Specific Access CodeSida OAI Dial Number Batch Transfer TMFAsyd Assignment of System Data MTC Equipped capacity of the Common Memory CM 1 ~ 4 Mbyte System Data Assign TableCalled Number Display when forwarding to Attendant Console Calling and Intermediate Station Number indication = # key/* key No CPU Mounted Status of IP00/1Not mounted/Mounted System Data Assign Table HEX/ASCII Data BIT System Data Contents Lstn Dfln Display of Location Free NumberingPstn RSCAsydn Assignment of System Data in NDM Asydn Asydl Assignment of System Data into Local DM LDM Example Subnet Mask Example IP AddressDefault Gateway Address Office Data Design ASYD/ASYDL Procedure for Setting Basic Office Data for OAI SystemASYDL-SYS1 INDEX513 Hex LDM usageAokc AkydAoac AnpdProcedure for Setting Office Data for OAI Services Using Conditions Abnormal Sequence Assignment Asyd System Data B6 1 OAI service is not availableSYS1 Index Call ID Notification Smfn for Isdn Functional Outline Isdn Caller’s Number Information ≤ n ≤ TMM Text Mail ModuleFacsimile Mail Module FMMAbnormal Sequence NEAX2400 IMX DLC TSW SYS1 Index TCP/IP Address Assignment from MAT Functional Outline Index SYS1Name Display Functional Outline INDEX79 INDEX78INDEX241 Asyd SYS1 INDEX78Called party Catching call from other internal lineCcis B6 = 1 OAI Service is not in service B6 = 0 OAI Service is in serviceAsyd SYS1 Index B1 = 0 Name Display 8-digitOAI Fusion ASYDL/ASYDN Assignment of System Data Data for OAI FusionINDEX533 FPC number of the node that has the standard VndmMultiple IPs Functional Outline III III PBX Example of Use of Facility on Fusion Network This page is for your notes Maintenance Maintenance System Messages System Fault Contents of FaultSystem Message 4-R System Message 4-R TCP/IP Link Failure 1. Print-out FormatTCP/IP Link Failure NEC ESD= OAI System Message 26-VLAN Interface Error Report= MIS ACD Flow of Fault Repair Fault DiagnosisDiagnosis from System Messages Start Repairing Procedure for TCP/IP Link Failure Message 4-RND-70895 Echapter Revision This page is for your notes