NEC ND-70895 (E) system manual Name Display Functional Outline

Page 84

OFFICE DATA DESIGN

Procedure for Setting Office Data for OAI Services

3.5 Name Display

3.5.1Functional Outline

This service is for displaying information (user’s name, station number, etc.) on the LCD of Dterm.

1.Catch internal call

2.Catch Forwarding Call from Call Forwarding Busy Line, Call Forwarding Absent, Call Forwarding Don’t Answer, Station Hunting, or etc..

3.5.2Using Conditions

1.Maximum 16 digits of user’s information can be displayed on LCD according to internal numbers.

2.What is available for this service to display, is alphabet, digit, sign or etc..

3.For administrating user’s information clearly, it is not available to use both “Name Display Service” which is assigned by ANDD command and “OAI Service” at same time.

4.It is not available to use both 8-digit Display Service and 16-digit Display Service at same time. For changing from 8-digit Display Service to 16-digit Display Service, can be changed by using “System Data”.

5.There are limitations below for 16-digit Display Service.

•User’s information can not be displayed on the top line of LCD.

•User’s information is displayed from the left side of bottom line and if the information is less than 16-digit, the rest of frames will be blank.

•It is not able to set multi-line on this Dterm.

6. There is a limitation below for 8-digit Display Service.

•User’s information is displayed from the middle of top line and if the information is less than 8 digits, the rest of frames will be blank. And the bottom line will display the clock.

7.If the user’s information is not assigned, normally station number will be displayed.

8.There is no guarantee for the user’s information since you change from 16-digit Display Service to 8-digit Display Service.

9.The service will be effective, if either of calling party or called party has Dterm which has the LCD.

CHAPTER 5

ND-70895 (E)

Page 74

Revision 1.0

Image 84

Contents ND-70895 E Stock #Liability Disclaimer NEC America, IncNEAX2400 IMX Issue No NEAX2400 IMX OAI System ManualTable of Contents ND-70895 Etable of Contents Page iii Revision List of Figures List of Tables This page is for your notes How to Follow the Manual Configuration of this manual is shown in TableGeneral Introduction System Outline Explains the outline of the OAI systemSystem Outline Block Concept of MSF Concept of TMF Concept of ACF Concept of TCF Concept of NTF 11 Concept of RCF 13 Concept of ATF Join of Facilities and Application System Configuration Symbol Symbol Name Circuit Card Remarks Dual System Configuration of NEAX2400 IMX IMG 15 IP Dual System ConfigurationInterface with External Computer Circuit Card Interface ConditionsThis page is for your notes Installation Procedure Cable Connections with External Computer OAI Software Installation System DATA=OVERRIDE/LOADChange system data written in DM Asyd SYS1Assign the system data written in LDM Asydl SYS1 INDEX512INDEX513 Upgrading OAI System from NEAX2400 ICS to NEAX2400 IMX This page is for your notes Commands This section explains the construction of each commandConfiguration of Commands for OAI System Configuration of Commands of the NEAX2400 IMX OAI SystemCommands This section explains the commands in used in the OAI SystemInterrelation among OAI System Commands Aadt Assignment of Announcement/Dictation Trunks TypeMsgt WaitDisconnect Timer = Impossible = Possible Announcement/Dictation Trunk Data Assignment TableAcno Assignment of Conversion Number Data AmnoLcno LrtdConversion Number Data Assignment Table Akyd Assignment of Key Data for Dterm Amno Assignment of Monitored Number MNONMI UCDMonitored Number Assignment Table Aoac Assignment of OAI Access Code KindLoac OAI Access Code Data Assignment Table Aokc Assignment of OAI Key Code Related Commands List Up Lokc Kind = 1 OP-CODE = 128 ~ Kind = 2 OP-CODE = 192 ~OAI Key Code Data Assignment Table Operation Code Remarks Aspa Assignment of Specific Access Code Service Feature Index aSida OAI Dial Number Batch Transfer TMFAsyd Assignment of System Data MTC System Data Assign Table Equipped capacity of the Common Memory CM 1 ~ 4 MbyteCalled Number Display when forwarding to Attendant Console Calling and Intermediate Station Number indication = # key/* key No CPU Mounted Status of IP00/1Not mounted/Mounted System Data Assign Table HEX/ASCII Data BIT System Data Contents Dfln Display of Location Free Numbering LstnPstn RSCAsydn Assignment of System Data in NDM Asydn Asydl Assignment of System Data into Local DM LDM Example IP Address Example Subnet MaskDefault Gateway Address Office Data Design Procedure for Setting Basic Office Data for OAI System ASYD/ASYDLASYDL-SYS1 INDEX513 Hex LDM usageAkyd AokcAoac AnpdProcedure for Setting Office Data for OAI Services Using Conditions Abnormal Sequence B6 1 OAI service is not available Assignment Asyd System DataSYS1 Index Call ID Notification Smfn for Isdn Functional Outline Isdn Caller’s Number Information ≤ n ≤ Text Mail Module TMMFacsimile Mail Module FMMAbnormal Sequence NEAX2400 IMX DLC TSW SYS1 Index TCP/IP Address Assignment from MAT Functional Outline SYS1 IndexName Display Functional Outline INDEX78 INDEX79INDEX241 Asyd SYS1 INDEX78Catching call from other internal line Called partyCcis B6 = 0 OAI Service is in service B6 = 1 OAI Service is not in serviceAsyd SYS1 Index B1 = 0 Name Display 8-digitOAI Fusion Assignment of System Data Data for OAI Fusion ASYDL/ASYDNINDEX533 FPC number of the node that has the standard VndmMultiple IPs Functional Outline III III PBX Example of Use of Facility on Fusion Network This page is for your notes Maintenance Maintenance System Fault Contents of Fault System MessagesSystem Message 4-R TCP/IP Link Failure 1. Print-out Format System Message 4-RTCP/IP Link Failure NEC ESDSystem Message 26-VLAN Interface Error Report = OAI= MIS ACD Fault Diagnosis Flow of Fault RepairDiagnosis from System Messages Repairing Procedure for TCP/IP Link Failure Message 4-R StartND-70895 Echapter Revision This page is for your notes