Panasonic KX-TG2352PW Caller ID Number Auto Edit Feature, Ringer setting, HInitial set

Page 29

The Caller ID Number Auto Edit Feature

There are 3 patterns of phone number (a, b, and c on p. 28). This feature allows your phone to automatically edit an in-coming Caller ID number into one pattern you preferred, and displays the Caller ID number with that pattern on the handset automatically.

After this feature is activated, Caller ID numbers coming from considered area codes (201, for example), from which the Caller ID numbers have been chosen to follow the desired pattern (7 digit pattern, for example), will be automatically edited from other patterns (11 digit pattern, for example) into the same pattern you have previously selected (which is 7 digit pattern, in the example).

Up to 4 area codes are allowed for this feature for patterns a, b and c (p. 28).

To activate this feature, you must (1) set this feature to on, and (2) make an out-going call from Caller List (p. 27) with a number which has one of 3 patterns that you have edited with considered area code, and that you prefer to be followed by future Caller ID numbers, so that in the future all the Caller ID numbers coming from the same area code will be displayed in the same pattern.

The Caller ID number Auto Edit feature is preset to ON at factory.

•If you fail to reach your destination when making the call, the phone number you dialed might have an incorrect pattern, please edit the phone number with another pattern (p. 28).

For example, if you move to another area, you may need to turn this feature to OFF to erase previously edited area codes. Then, if still need, you may activate this feature again.

Make sure the unit is not being used and the handset is lifted off the base unit.

1. Press (MUTE/FUNCTION).

 

2. Scroll to “Initial set” by pressing Ö or Ñ,

 

Ringer setting

and press á.

HInitial set

 

 

--------------

 

 

Basic Operation

3.Scroll to “Caller ID edit” by pressing Ö or Ñ, and press á.

4.Select “On” or “Off” by pressing Ö or Ñ.

5.Press á (Save key).

•A beep sounds.

•To exit the programming mode, press (OFF).

Auto talk HCaller ID edit

Set tel line

Auto edit

:On

GF H=Save

•When the feature is set to OFF, the unit will still be able to display Caller ID, like regular Caller ID telephone, but the in-coming Caller ID number will not be edited by pattern and by area codes.

For assistance, please call: 1-800-211-PANA(7262)

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Operating Instructions Charge the battery for about 15 hours before initial useEnergy Star Attach your purchase receipt hereBase Unit Location/Noise Battery ChargeFor Best Performance Contents Storing Names and Numbers Canceling the Handset RegistrationALL, 1 to 3 p Charge Contacts p Charge Indicator pHandset Locator Buttons Handset How to use the Navigator keyConnections InstallationBase unit Charger unitBattery Charge Installing the Battery in the HandsetBattery information Battery strengthDisplay prompt Battery strength RechargeOptional Headset Belt ClipProgramming Guidelines Programmable SettingsHow to select a function item from the menu Useful information Function Menu TableSelect Pulse or Tone by pressing Ö or Press á Save key Dialing ModeGF H=Save Line ModeSelect a or B by pressing Ö or Ñ Press á Save key Select On or Off by pressing Ö or Ñ Press á Save key Auto Talk FeatureScroll to Ringer setting by pressing Ö or Ñ, and press á Ringer VolumeSelect the desired volume by pressing Ö or Ñ To turn the ringer onLCD Contrast Ringer setting HInitial set Hlcd contrast Auto talkLCD contrast Low High =Save LCD contrast Low HighPress ALL on base for 3 sec, then press H Base unitHandset Handset RegisteringBack side Registration for Additional HandsetsHands-free Digital Duplex Speakerphone To dial after confirming the entered number To redial using the redial list Memory RedialTo redial the last number dialed on the handset Press or and press PAUSE/REDIALTo release the hold To put a call on holdLighted handset keypad Backlit LCD displayAuto Talk Answering CallsHow caller information is displayed when a call is received Caller ID ServiceViewing the Caller List Using the Caller List12344567890 Editing the Caller’s Phone Number Ringer setting Caller ID Number Auto Edit FeatureScroll to Initial set by pressing Ö or Ñ HInitial setScroll to Save directory by pressing Ö or Ñ, and press á Storing Caller List Information in the DirectoryEnter name IH G=NextTo erase a specific caller from the Caller List Erasing Caller List InformationTo erase all entries in the Caller List Caller list 10 new calls GF H=DirectoryDirectory Tom Jones =Edit H=Save Press Ö Next key Enter a phone number, up to 22 digitsIf you make a mistake while entering a name Selecting characters to enter namesFor example, to enter Tom Jones Press Ü or á to enter the directory list Dialing from the DirectoryScroll to the desired item by pressing Ö or Ñ To search for a name by initialEditing When finished, press á Save keyPress Ö Next key Add a number to the current number Press Ö Next keyHelen Clear? =No CLEAR=Yes ErasingIntercom Auto Talk Answering Intercom CallsCall from Intercom 00-00-03 To transfer a call from the handset Transferring a CallCall Share ConferenceEx. a conference call with Handset 1 To join a conversation Call ShareStoring a Voice Mail Access Number Voice Mail ServicePress Ö Save key To erase a stored numberPress á at VM tone detect Setting the Voice Mail VM Tone DetectionListening to Voice Mail Messages Save directory HV.M. access Ringer settingTo listen to your voice mail messages After the voice mail box has received messagesFor Rotary or Pulse Service Users Special FeaturesTemporary Tone Dialing Muting Your ConversationHow to Use the Pause Button For Call Waiting Service UsersCall Waiting Caller ID Feature For PBX Line/Long Distance CallsSelecting the flash time Flash ButtonOr Ñ Press á Scroll to Set flash time by pressingIncoming Call Tone Ringer ToneWall Mounting To charge the handset battery Wall Mounting Adding Another PhoneBattery Replacement Canceling the Handset Registration Canceling Registration/Re-registrationPress á at Registration Re-registering the HandsetPress and hold Handset Locator #Press áIf the Following Appear Base unit. To cancel another handset When trying to store an item in the directory,Directory memory is full. To erase other items From the directory, seeProblem TroubleshootingYou cannot program items, Programming is not possible while Problem Cause & RemedyTo page. Try again later Recharge is displayed, Charge the battery fully pOr the base unit. Try again later Displayed and/or Continues to flash, orOnly Important Safety Instructions Useful Information FCC and Other Information For assistance, please call 1-800-211-PANA7262 FCC and Other Information Base unit SpecificationsIndex Auto Talk FeatureLimited Warranty Coverage Panasonic Telephone Products Limited WarrantyCustomer Services Directory When you ship the product For product serviceFor your future reference Serial No Date of purchase
Top Page Image Contents