Panasonic KX-TG2352W, KX-TG2352PW operating instructions Troubleshooting, Problem

Page 58

Troubleshooting

Problem

Cause & Remedy

The unit does not work.

•Check the settings (p. 8–10).

•Check whether the dialing mode setting is correct (p. 14).

•Charge the battery fully (p. 9, 10).

•Clean the charge contacts and charge again (p. 10).

•Install the battery properly (p. 9).

•Unplug the AC adaptor of the base unit to reset. Plug in, and try again.

•The handset has not been registered to the base unit. Register the handset (p. 19, 55).

•Re-install the battery (p. 53) and charge it fully.

“No link to base	•You are too far from the base unit.
Move closer to base,	Move closer to the base unit and try again.
try again” is displayed	•Plug in the AC adaptor of the base unit.
and an alarm tone sounds.	•Raise the base unit antenna.

Static, sound cuts in/out,	•Locate the handset and the base unit away
fades. Interference from	from other electrical appliances (p. 3).
other electrical units.	•Move closer to the base unit.
	•Raise the base unit antenna.

The handset does not ring.	•The ringer volume is OFF. Set to HIGH or
	MEDIUM or LOW (p. 17).
	•While you are making an intercom call, these
	handsets do not ring. Instead users will hear
	incoming call tones (p. 49).

The handset display is	•Charge the battery fully (p. 9, 10).
blank.

58

Image 58

Contents Charge the battery for about 15 hours before initial use Operating InstructionsAttach your purchase receipt here Energy StarFor Best Performance Battery ChargeBase Unit Location/Noise Contents Canceling the Handset Registration Storing Names and NumbersHandset Locator Buttons Charge Contacts p Charge Indicator pALL, 1 to 3 p How to use the Navigator key HandsetBase unit InstallationConnections Charger unitInstalling the Battery in the Handset Battery ChargeDisplay prompt Battery strength Battery strengthBattery information RechargeBelt Clip Optional HeadsetHow to select a function item from the menu Programmable SettingsProgramming Guidelines Function Menu Table Useful informationDialing Mode Select Pulse or Tone by pressing Ö or Press á Save keySelect a or B by pressing Ö or Ñ Press á Save key Line ModeGF H=Save Auto Talk Feature Select On or Off by pressing Ö or Ñ Press á Save keySelect the desired volume by pressing Ö or Ñ Ringer VolumeScroll to Ringer setting by pressing Ö or Ñ, and press á To turn the ringer onLCD contrast Low High =Save Ringer setting HInitial set Hlcd contrast Auto talkLCD Contrast LCD contrast Low HighHandset Base unitPress ALL on base for 3 sec, then press H Handset RegisteringRegistration for Additional Handsets Back sideHands-free Digital Duplex Speakerphone To redial the last number dialed on the handset To redial using the redial list Memory RedialTo dial after conﬁrming the entered number Press or and press PAUSE/REDIALLighted handset keypad To put a call on holdTo release the hold Backlit LCD displayAnswering Calls Auto TalkCaller ID Service How caller information is displayed when a call is receivedUsing the Caller List Viewing the Caller List12344567890 Editing the Caller’s Phone Number Scroll to Initial set by pressing Ö or Ñ Caller ID Number Auto Edit FeatureRinger setting HInitial setEnter name Storing Caller List Information in the DirectoryScroll to Save directory by pressing Ö or Ñ, and press á IH G=NextTo erase all entries in the Caller List Erasing Caller List InformationTo erase a speciﬁc caller from the Caller List Caller list 10 new calls GF H=DirectoryDirectory Press Ö Next key Enter a phone number, up to 22 digits Tom Jones =Edit H=SaveFor example, to enter Tom Jones Selecting characters to enter namesIf you make a mistake while entering a name Scroll to the desired item by pressing Ö or Ñ Dialing from the DirectoryPress Ü or á to enter the directory list To search for a name by initialPress Ö Next key Add a number to the current number When ﬁnished, press á Save keyEditing Press Ö Next keyErasing Helen Clear? =No CLEAR=YesIntercom Call from Intercom 00-00-03 Answering Intercom CallsAuto Talk Transferring a Call To transfer a call from the handsetEx. a conference call with Handset 1 ConferenceCall Share To join a conversation Call ShareVoice Mail Service Storing a Voice Mail Access NumberTo erase a stored number Press Ö Save keySetting the Voice Mail VM Tone Detection Press á at VM tone detectTo listen to your voice mail messages Save directory HV.M. access Ringer settingListening to Voice Mail Messages After the voice mail box has received messagesTemporary Tone Dialing Special FeaturesFor Rotary or Pulse Service Users Muting Your ConversationCall Waiting Caller ID Feature For Call Waiting Service UsersHow to Use the Pause Button For PBX Line/Long Distance CallsOr Ñ Flash ButtonSelecting the flash time Press á Scroll to Set flash time by pressingRinger Tone Incoming Call ToneWall Mounting To charge the handset battery Adding Another Phone Wall MountingBattery Replacement Canceling Registration/Re-registration Canceling the Handset RegistrationPress and hold Handset Locator Re-registering the HandsetPress á at Registration #Press áIf the Following Appear Directory memory is full. To erase other items When trying to store an item in the directory,Base unit. To cancel another handset From the directory, seeTroubleshooting ProblemProblem Cause & Remedy You cannot program items, Programming is not possible whileOr the base unit. Try again later Recharge is displayed, Charge the battery fully pTo page. Try again later Displayed and/or Continues to flash, orOnly Important Safety Instructions Useful Information FCC and Other Information For assistance, please call 1-800-211-PANA7262 FCC and Other Information Specifications Base unitAuto Talk Feature IndexPanasonic Telephone Products Limited Warranty Limited Warranty CoverageCustomer Services Directory For your future reference For product serviceWhen you ship the product Serial No Date of purchase