Panasonic KX-TG2352W, KX-TG2352PW operating instructions FCC and Other Information

Page 66

FCC and Other Information

CAUTION:

To comply with FCC RF exposure requirements, the base unit should be installed with its antenna located at 20 cm or more from persons and handset should be carried with the specific belt-clip provided for the handset to ensure compliance. Other non-tested belt-clips or similar body-worn accessories may not comply, therefore, should be avoided.

This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section 68.316.

When you hold the phone to your ear, noise might be heard in your Hearing Aid. Some Hearing Aids are not adequately shielded from external RF (radio frequency) energy. If noise occurs, use an optional headset accessory or the speakerphone option (if applicable) when using this phone. Consult with your audiologist or Hearing Aid manufacturer about the availability of Hearing Aids which provide adequate shielding to RF energy commonly emitted by digital devices.

Environment — do not place the unit in a room where the temperature is less than 5°C (41°F) or greater than 40°C (104°F). Allow 10 cm (4") clearance around the unit for proper ventilation. Avoid excessive smoke, dust, mechanical vibration, shock, or direct sunlight.

Medical — consult the manufacturer of any personal medical devices, such as pacemakers or hearing aids, to determine if they are adequately shielded from external RF (radio frequency) energy. (The unit operates in the frequency range of 2400MHz to 2480MHz, and the power output level can range 0.04 watts to 0.40 watts.) Do not use the unit in health care facilities if any regulations posted in the area instruct you not to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF (radio frequency) energy.

Routine care — wipe the unit with a soft cloth. Do not use benzine, thinner, or any abrasive powder. When you leave the unit unused for a long period of time, unplug the AC adaptor from the outlet.

If there is any trouble — disconnect the unit from the telephone line and connect a known working phone. If the known working phone operates properly, have your unit repaired by a Factory Servicenter or other Authorized Servicer. If the known working phone does not operate properly, consult your telephone company.

66

Image 66
Contents Charge the battery for about 15 hours before initial use Operating InstructionsAttach your purchase receipt here Energy StarBattery Charge For Best PerformanceBase Unit Location/Noise Contents Canceling the Handset Registration Storing Names and NumbersCharge Contacts p Charge Indicator p Handset Locator ButtonsALL, 1 to 3 p How to use the Navigator key HandsetBase unit InstallationConnections Charger unitInstalling the Battery in the Handset Battery ChargeDisplay prompt Battery strength Battery strengthBattery information RechargeBelt Clip Optional HeadsetProgrammable Settings How to select a function item from the menuProgramming Guidelines Function Menu Table Useful informationDialing Mode Select Pulse or Tone by pressing Ö or Press á Save keyLine Mode Select a or B by pressing Ö or Ñ Press á Save keyGF H=Save Auto Talk Feature Select On or Off by pressing Ö or Ñ Press á Save keySelect the desired volume by pressing Ö or Ñ Ringer VolumeScroll to Ringer setting by pressing Ö or Ñ, and press á To turn the ringer onLCD contrast Low High =Save Ringer setting HInitial set Hlcd contrast Auto talkLCD Contrast LCD contrast Low HighHandset Base unitPress ALL on base for 3 sec, then press H Handset RegisteringRegistration for Additional Handsets Back sideHands-free Digital Duplex Speakerphone To redial the last number dialed on the handset To redial using the redial list Memory RedialTo dial after confirming the entered number Press or and press PAUSE/REDIALLighted handset keypad To put a call on holdTo release the hold Backlit LCD displayAnswering Calls Auto TalkCaller ID Service How caller information is displayed when a call is receivedUsing the Caller List Viewing the Caller List12344567890 Editing the Caller’s Phone Number Scroll to Initial set by pressing Ö or Ñ Caller ID Number Auto Edit FeatureRinger setting HInitial setEnter name Storing Caller List Information in the DirectoryScroll to Save directory by pressing Ö or Ñ, and press á IH G=NextTo erase all entries in the Caller List Erasing Caller List InformationTo erase a specific caller from the Caller List Caller list 10 new calls GF H=DirectoryDirectory Press Ö Next key Enter a phone number, up to 22 digits Tom Jones =Edit H=SaveSelecting characters to enter names For example, to enter Tom JonesIf you make a mistake while entering a name Scroll to the desired item by pressing Ö or Ñ Dialing from the DirectoryPress Ü or á to enter the directory list To search for a name by initialPress Ö Next key Add a number to the current number When finished, press á Save keyEditing Press Ö Next keyErasing Helen Clear? =No CLEAR=YesIntercom Answering Intercom Calls Call from Intercom 00-00-03Auto Talk Transferring a Call To transfer a call from the handsetEx. a conference call with Handset 1 ConferenceCall Share To join a conversation Call ShareVoice Mail Service Storing a Voice Mail Access NumberTo erase a stored number Press Ö Save keySetting the Voice Mail VM Tone Detection Press á at VM tone detectTo listen to your voice mail messages Save directory HV.M. access Ringer settingListening to Voice Mail Messages After the voice mail box has received messagesTemporary Tone Dialing Special FeaturesFor Rotary or Pulse Service Users Muting Your ConversationCall Waiting Caller ID Feature For Call Waiting Service UsersHow to Use the Pause Button For PBX Line/Long Distance CallsOr Ñ Flash ButtonSelecting the flash time Press á Scroll to Set flash time by pressingRinger Tone Incoming Call ToneWall Mounting To charge the handset battery Adding Another Phone Wall MountingBattery Replacement Canceling Registration/Re-registration Canceling the Handset RegistrationPress and hold Handset Locator Re-registering the HandsetPress á at Registration #Press áIf the Following Appear Directory memory is full. To erase other items When trying to store an item in the directory,Base unit. To cancel another handset From the directory, seeTroubleshooting ProblemProblem Cause & Remedy You cannot program items, Programming is not possible whileOr the base unit. Try again later Recharge is displayed, Charge the battery fully pTo page. Try again later Displayed and/or Continues to flash, orOnly Important Safety Instructions Useful Information FCC and Other Information For assistance, please call 1-800-211-PANA7262 FCC and Other Information Specifications Base unitAuto Talk Feature IndexPanasonic Telephone Products Limited Warranty Limited Warranty CoverageCustomer Services Directory For your future reference For product serviceWhen you ship the product Serial No Date of purchase