Panasonic KX-TG2314 manual Troubleshooting

Page 58

Troubleshooting

If the handset display shows error messages, see “If the Following Appear on Your Display...” (p. 50 – 51) for the Cause & Remedy.

Problem

Cause & Remedy

“No link to base. Move

closer to base, try again.” is displayed and an alarm tone sounds.

•You are too far from the base unit. Walk closer to the base unit.

•Confirm the base unit’s AC adaptor is plugged in.

•Raise the base unit antenna.

•If the above remedies do not solve the problem, the handset may have lost communication with the base unit. Register the handset again (p. 45).

The handset and/or base unit does not work.

•Check the settings (p. 8 –10).

•Check whether the dialing mode setting is correct (p. 13).

•Fully charge the battery (p. 9).

•Clean the charge contacts and charge again (p. 10).

•Check battery Installation (p. 9).

•Unplug the base unit’s AC adaptor to reset it. Plug in, and try again.

•Re-install the battery (p. 9) and fully charge it.

Static, sound cuts in/out,	• Move the handset and base unit away from
fades. Interference from other	other electrical appliances (p. 3).
electrical units.	• Walk closer to the base unit.
	• Raise the base unit antenna.

The handset does not ring.	• The ringer volume is turned off. Set to high,
	medium, or low (p. 15).

The handset display is blank.	• If the handset display is blank, fully charge
	the battery (p. 9).

You cannot program any	• Programming is not possible while the
function items.	handset and/or base unit is being used.
	• Do not pause for over 60 seconds while
	programming.
	• Walk closer to the base unit.

While programming or searching, the handset starts to ring and the program/ search stops.

•A call is coming in. To answer the call, press [C] or [s]. Start again from the beginning after hanging up.

52

Image 58

Contents Page Page Page Page Page Page GHz Multi-Handset Digital Cordless Phone Charge the battery for 6 hours before initial useModel No. KX-TG2314 Pulse-or-tone dialing capability Attach your purchase receipt here Accessories included Base Unit Location/Noise Battery ChargeFor Best Performance For assistance, please call 1-800-211-PANA7262Contents Contents Handset Location of ControlsBase unit HOLD/INTERCOM ButtonHandset soft keys Location of ControlsCharger unit Handset navigator keyInstallation ConnectionsTo replace the battery Installation Installing the Battery in the HandsetBattery strength Display prompt Battery strengthBattery replacement InstallationBattery information RechargeHow to select a function item from the menu Programmable SettingsProgramming Guidelines Handset Programmable Settings Function Menu Table Handset Sub-menuProgrammable Settings Display Language Handset Dialing Mode HandsetProgrammable Settings Line Mode Handset Auto Talk HandsetSelect the desired volume level by pressing d or B Programmable Settings Ringer Volume HandsetPress Menu Scroll to Ringer setting by pressing d Or B , then press SelectSelect the desired ringer tone by pressing d Programmable Settings Ringer Tone HandsetScroll to Ringer tone by pressing d or Or BScroll to LCD contrast by pressing d or Programmable Settings LCD Contrast HandsetMessage Alert Handset Select the desired contrast by pressing d orTo have a hands-free phone conversation Making CallsHands-free Digital Duplex Speakerphone To dial after confirming the entered number To redial using the redial list Memory RedialMaking Calls To redial the last number dialedBacklit LCD display/Lighted handset keypad To turn this feature on, press VE during aVoice Enhancer Technology ConversationOFF s Auto Talk Answering CallsOr OFF To transfer the call to another person, seePersonalized Name Display Caller ID ServiceHow Caller ID information is displayed Display MeaningPress Rcvd calls, d, or B to enter Using the Caller ListViewing the Caller List Handset Caller ListWhat , means Using the Caller ListCalling Back from the Caller List Handset If a caller calls more than onceTo call the edited number, press C or s Press Select Press Edit repeatedly until the number isShown in the desired format To save the edited number into the phone book, press SaveScroll to Caller ID edit by pressing d Using the Caller List Caller ID Number Auto Edit HandsetTo turn Caller ID Number Auto Edit on or off Select Off or On by pressing d or BPress Rcvd calls, d, or B to enter the Caller List Press SelectTo erase a specific caller Using the Caller List Erasing Caller Information HandsetTo erase all entries Phone Book Storing Names and Numbers HandsetSelecting characters to enter names If you make a mistake when entering a name or numberPhone Book For example, to enter TomPhone Book Dialing from the Phone Book Handset To search for a name by initialWhile you are on a call Chain Dial HandsetIndex table Press Menu Search for the desired item by pressing d orPhone Book Editing an Item in the Phone Book Handset Erasing an Item in the Phone Book HandsetPress Menu Scroll to Copy phone book by pressing d Phone Book Copying Items in the Phone Book HandsetTo copy one phone book item to another handset Press Select at Copy 1 itemScroll to Copy all items by pressing d Receiving then Phone book Received Tom Jones 01/10Ex. From the Handset 1 to the Handset IntercomPaging between Handsets Handset During an intercom callFrom a Handset to another Handset Transferring a CallQuick call transfer Conference Calls To join a conversation Call ShareStoring a Voice Mail Access Number Handset Voice Mail ServiceTo erase a stored voice mail access number Scroll to VM tone detect by pressing d VM tone detect KBack dB SaveLPress Menu Press Select at V.M. access Voice Mail Service Listening to Voice Mail Messages HandsetTo listen to your voice mail messages Handset Locator Base Unit Special FeaturesFor Rotary or Pulse Service Users Handset Temporary Tone DialingCall Waiting Caller ID display Special Features For Call Waiting Service Users HandsetUsing the Pause Key For PBX Line/Long Distance CallsSelecting the flash time Special Features Flash Button HandsetIncoming Call Tone Handset Select the desired time by pressing d or BKey tone On KBack dB SaveL Special Features Key Tone HandsetScroll to Key tone by pressing d or B Handset RegisteringBelt Clip Connecting an optional headsetTo switch to the speakerphone while using the headset Optional HeadsetTo charge the handset battery Wall MountingWall Mounting Wall Template for the Charger unitMenu item Command Selection items Direct CommandsDuring programming If the Following Appear on Your Display Display message Cause & RemedyNo items stored If the Following Appear on Your DisplayIncomplete Line in useTroubleshooting Problem Cause & Remedy Recharge battery isTroubleshooting Important Safety Instructions Important Safety Instructions FCC and Other InformationFCC and Other Information FCC RF Exposure Warning Index Index RegistrationLimited Warranty Limits And Exclusions Limited Warranty CoverageMail-In Service Ave de Infanteria, KmCustomer Services Directory For your future reference For product service When you ship the productPage Page Page Page Page Page