Panasonic Installation Guide for the Message Expansion Card for DISA/UCD OGMs

Page 52

2.3 Installing Optional Service Cards

2.3.7Message Expansion Card for DISA/UCD OGMs (KX- TE82491)

Function

When an optional message expansion card for DISA/UCD OGMs is added, up to 2 messages can be played simultaneously for callers and the total recording time of the PBX is increased from 3 to 6 minutes.

1.Loosen the screws and open the top and bottom front covers. (2.2.3 Opening/Closing Covers)

2.Slide the card between the guiderails until it clicks, and attach the connector to it.

KX-TE82491

Note

Use extra care to make sure you do not damage the part of the case marked with a circle.

3.Close the covers and secure the screws. (2.2.3 Opening/Closing Covers)

Note

To uninstall the card, follow the instructions illustrated below.

2

1

1.Push the catch on the side of one guardrail in the direction of the arrow to release it.

2.Lift the edge of the card while holding the catch open. (Do not touch the circuit board of the card during the operation.)

52

Installation Manual

Image 52
Contents Installation Manual Advanced Hybrid SystemSystem Components Abbreviations in this manual Compatible Proprietary TelephonesImportant Safety Instructions Precautions For users in New Zealand onlyFor users in Australia only For users in Taiwan onlyFor Future Reference For users in Finland, Norway and Sweden onlyHttp//doc.panasonic.de Introduction Precautions for Users in the United Kingdom For Your SAFETY, Please Read the Following Text CarefullyInstallation Manual Table of Contents Guide for KX-TE Maintenance Console Section System Outline System Highlights System HighlightsBasic System Construction Main UnitSystem Connection Diagram Outside CO LineSpecifications General DescriptionCharacteristics System Capacity System CapacityMaximum Cards and Terminal Equipment System DataMax. Quantity Section Installation Before Installing Before InstallingSafety Installation Instructions Installation PrecautionsBefore Installing Installing the Advanced Hybrid System UnpackingNames and Locations Opening/Closing Covers Opening CoversClosing Covers Securing Cords To remove the rivet, use a screwdriver as shown below Connecting Frame Earth Connect the frame of the PBX to earthConnecting Backup Batteries Battery Rating 24 Ah Wall Mounting Mounting on a Wooden WallMounting on a Concrete or Mortar Wall Installing the Advanced Hybrid System Installation Installing Surge ProtectorOverview Outside Installation Installation of an Earth RodInstalling the Advanced Hybrid System Installing Optional Service Cards Location of Optional Service CardsInstalling KX-TE82483 to KX-TES824 FunctionInstalling Optional Service Cards Installing KX-TE82480 to KX-TES824 Installing Optional Service Cards Installing Optional Service Cards Installing KX-TE82480 to KX-TEM824 Installing Optional Service Cards Installing KX-TE82474 to KX-TES824 4 8-Port SLT Extension Card KX-TE82474Installing Optional Service Cards Installing KX-TE82474 to KX-TEM824 5 3-Port Caller ID Card KX-TE82493 6 4-Port Doorphone Card KX-TE82461 Message Expansion Card for DISA/UCD OGMs KX- TE82491 8 2-Channel Voice Message Card KX-TE82492 Connecting Outside CO Lines Connecting Outside CO LinesConnection Connecting Extensions Connecting ExtensionsMaximum Cabling Distance of Extension Wiring Twisted Cable Telephone Wiring Connecting Extensions in Parallel Connecting Doorphones and Door Openers Connecting Doorphones and Door OpenersInstalling the Doorphone KX-T30865 Maximum Cabling DistanceConnecting Doorphones and Door Openers Connecting Doorphones KX-T30865 Connecting Door Openers Connecting Doorbell or Door Chime Connecting Doorbell or Door ChimeConnecting Peripherals Connecting PeripheralsPager PC/Printer via RS-232CFor connecting a PC/printer with a 9-pin RS-232C connector Circuit Type Signal Name FunctionFor connecting a PC/printer with a 25-pin RS-232C connector PC via USB 1.1 interface Power Failure Connections Power Failure ConnectionsStarting the Advanced Hybrid System Starting the Advanced Hybrid SystemStarting the Advanced Hybrid System Starting the Advanced Hybrid System Section Guide for KX-TE Maintenance Console Installing KX-TE Maintenance Console Installing KX-TE Maintenance Console on a PCSetting the Password and Password Security System RequirementsInstalling KX-TE Maintenance Console Click Maintenance ConsoleInstalling the USB Driver ConnectionConnection Serial Interface ConnectionWindows Me Windows 98SEWindows Windows XP Click Continue AnywayStarting KX-TE Maintenance Console for the first time Accessing PBX via Internal Modem → KX-TE Maintenance ConsoleSelect Auto Tone or Auto Pulse for Dial Type Click InitialiseConnection Connection Section Troubleshooting Troubleshooting InstallationCause Operation System Restart System Reset with System Data Clear Index Numerics Template for Wall Mounting Copyright
Related manuals
Manual 167 pages 36.9 Kb