Panasonic KX-TG2219B operating instructions Troubleshooting, ProblemRemedy

Page 54

Troubleshooting

ProblemRemedy

The unit does not work.

•Check the settings (p. 11–15).

•Charge the battery fully (p. 12).

•Clean the charge contacts and charge again (p. 13).

•Install the battery properly (p. 12).

•Place the handset on the base unit and unplug the AC adaptor to reset. Plug in, and try again.

•Re-install the battery and place the handset on the base unit (p. 52). Try again.

“No link to base

Place on cradle and try again.” is displayed and an alarm tone sounds.

•You are too far from the base unit. Move closer and try again.

•Place the handset on the base unit and try again.

•Plug in the AC adaptor.

•Raise the base unit antenna.

Static, sound cuts in/out, fades. Interference from other electrical units.

•Locate the handset and the base unit away from other electrical appliances (p. 3).

•Move closer to the base unit.

•Raise the base unit antenna.

•Press Ü to select a clearer channel in the talk or speakerphone mode.

The unit does not ring.

•The ringer volume is set to OFF. Set to HIGH or LOW (p. 18).

The handset display is blank. •Charge the battery fully (p. 12).

You cannot program items, •Programming is not possible while the

such as the dialing mode. unit is in the talk or speakerphone mode, when viewing the Caller List/directory list.

•Do not pause for over 60 seconds while programming.

•Move closer to the base unit.

•Ö, Ñ, Ü or á may have been pressed when you picked up the handset. Press (OFF) and try again.

54

Image 54

Contents Charge the battery for about 15 hours before initial use Operating InstructionsAttach your purchase receipt here Energy Star One Handset Cover Wall Mounting Belt Clip p Adaptor pOne Battery Charge For Best PerformanceBase Unit Location/Noise Contents Useful Information Location of Controls VM Voice Mail Indicator pIndicator p , 24, 26 Base unitButton p HandsetTone Button p Microphone pReceived callsG DisplayRecharge Received calls New calls GF H=Directory Voice mail V.E Ringer offAnn Paging WaitingPlease lift up and try again Directory full Save error DisplaySettings ConnectionsInstalling the Battery in the Handset Display prompt Battery strength Battery strengthBattery information RechargeDialing Mode GF H=SaveLine Mode PreparationProgrammable Functions Scroll to Auto talk by pressing Ö or Auto Talk FeatureScroll to Program by pressing Ö or Ñ Select On or Off by pressing Ö or ÑGF H=Save Ringer Ringer VolumeSave directory HRinger volume Ringer tone GF H=Save Ringer offScroll to Ringer tone by pressing Ö or Press á Ringer volume HRinger tone Program GF H=SaveRinger Tone Select the desired ringer tone by pressing Or ÑSelect the desired contrast by pressing Ö LCD ContrastScroll to LCD contrast by pressing Ö Ringer tone HProgram CallerID edit Hlcd contrastMaking Calls Talk V.ETalk V.E 00-00-00 Off V.E 00-01-08 SP-phone V.E Off V.E If noise interferes with the conversationSP-phone V.E Hands-free Digital Duplex SpeakerphoneTo redial using the redial list Memory Redial To dial after conﬁrming the entered numberTo redial the last number dialed on the handset To release the hold While usingTo put a call on hold LoudBacklit LCD display Voice Enhancer TechnologyLighted handset keypad Helpful hintAnswering Calls Auto TalkCaller ID Service How caller information is displayed when a call is receivedReceived calls Received calls G Using the Caller ListViewing the Caller List New calls GF H=DirectoryTo exit the Caller List Ex. When you search from the most recent callTo return to the previous caller Display meaning12344567890 Calling Back from the Caller ListHEdit Save directory Caller ID Number Auto Edit Feature pEditing the Caller’s Phone Number 321-5555 =Next H=EditCaller ID Number Auto Edit Feature Scroll to Program by pressing Ö or Ñ and press áAuto talk HCallerID edit LCD contrast Auto edit GF H=Save Edit HSave directory Storing Caller List Information in the DirectoryScroll to Save directory by pressing Ö or Ñ, and press á Enter name IH G=NextErasing Caller List Information To erase a speciﬁc caller from the Caller ListTo erase all entries in the Caller List Directory Storing Names and NumbersDialing buttons, Ü or á Press á at Save directoryEnter a name, up to 15 characters with Press Ö Next keyEntering Names and Symbols If you make a mistake while entering a nameNumber of times key is pressed Keys For example, to enter Tom Jones Ann Finding Stored ItemsDirectory list =Caller’s list To search for a name by initialKeys Index DialingIndex table Directory list =Caller’s list FrankEditing Erasing Helen Clear? =No H=Yes1234567PPP890 =Edit H=Save Save VM access# Voice Mail ServiceStoring a Voice Mail Access Number Scroll to Program by pressing Ö or Ñ Or ÑSetting the Voice Mail VM Tone Detection To erase a stored numberScroll to Program by pressing Ö or Ñ Press á Save VM acces# HVM tone detect Set line mode Listening to Voice Mail MessagesFor Rotary or Pulse Service Users Special FeaturesAutomatic Security Code Setting Temporary Tone DialingCall Waiting Caller ID Feature For Call Waiting Service UsersHow to Use the Pause Button Handset LocatorPress á at Set flash time Flash ButtonSelecting the ﬂash time Select the desired time by pressing Ö or ÑBelt Clip Connecting an optional headset to the handsetTo switch to the speakerphone while using the headset Optional HeadsetWall mounting adaptor, then Wall MountingTuck the telephone line cord inside Push it in the direction of the arrowMount the unit, then slide down To charge the handset batteryConnect the telephone line cord Fix the charge contacts # and insertBattery Replacement Adding Another Phone Troubleshooting ProblemRemedyUseful Information Problem Remedy Digits long, the number will not beImportant Safety Instructions Important Safety Instructions FCC and Other Information FCC and Other Information Useful Information Speciﬁcations For your future referenceBattery Charge IndexFor product service When you ship the product