Paradyne and 8985, 8968, 8965, 8955 manual Configuring ReachDSL Ports, Field Description

Page 14

3. Configuration Using the Web Interface

Configuring ReachDSL Ports (8955)

Use the Configuration - DSL Port screen to set parameters for a DSL port on the 8955 ReachDSL line card.

Procedure

To configure a ReachDSL port:

1.Select a Port from the drop-down list and click on Select. Current values for the port are displayed.

2.Enter or select the following fields:

Field

Description

 

 

Line Circuit Name

Enter a name from 1 to 255 characters long to indicate to

 

whom the port is assigned. The following values are

 

reserved and cannot be used: AVAILABLE (port is not

 

assigned), and FAULTY (port is faulty and can not be

 

assigned).

 

 

Line Code

The Line Code parameter currently has no effect on a

 

ReachDSL card.

 

 

DSL Line Profile Name

Enter the name of a DSL line profile to set rates for the

 

port.

 

 

DSL Alarm Profile Name

Enter the name of a DSL alarm profile to set alarm

 

thresholds for the port.

 

 

Equivalent Working Length

Specify the estimated length of the DSL line. This used to

 

limit transmit rates and maximum transmit power settings

 

according to local spectrum management guidelines.

 

 

Max Tx Power

Specify the maximum transmit power setting for the

 

ATU-C. The allowable Maximum Transmit Power range

 

may be limited according to local spectrum management

 

guidlines. The actual transmit power level will be based

 

upon the symbol rate selected to maximize the transmit

 

data rate and may be lower than the Maximum Transmit

 

Power level configured.

 

 

Far End Max Tx Power

Specify the maximum transmit power setting for the

 

ATU-R. The allowable Maximum Transmit Power range

 

may be limited according to local spectrum management

 

guidlines. The actual transmit power level will be based

 

upon the symbol rate selected to maximize the transmit

 

data rate and may be lower than the Maximum Transmit

 

Power level configured.

 

 

Port Status

Select Enabled, Disabled, or Reset from the drop-down

 

list to determine the status of the port.

 

 

3. Click on Apply.

3-2

June 2004

8900-A2-GB20-30

Image 14
Contents ATM Line Cards Copyright 2004 Paradyne Corporation All rights reserved Contents Connector Pin Assignments DiagnosticsMaintenance Procedures Technical Specifications IndexDocument Summary About This GuideDocument Purpose and Intended Audience Product-Related Documents Document Number Document TitleAbout the ATM Line Cards ATM Line CardsEndpoint Support Features ATM Line Card FeaturesATM Features Sample Network Configurations Endpoint with Voice InterfacesSnmp Trap Support Snmp Management CapabilitiesManagement Information Base MIB Support Logging Into the Web Interface Accessing the SCP Card Web InterfaceIntroduction Help Button Ending a SessionIf you would like to configure Card using See Configuration Using the Web InterfaceConfiguring Spectrum Management OverviewConfiguring ReachDSL Ports Field DescriptionConfiguring Adsl Ports 8965 Disabled Power management is disabled Configuring Shdsl Ports Configuring Line Profiles 8955, 8965 Upstream / Far End ProfileCreating Line Profiles for Ports Configuring Alarm Threshold Profiles 8955, 8965 Downstream / Near End Alarm ProfileLoss of Signal Seconds Creating Alarm Threshold Profiles for Model Violations in a 15-minute interval equals or exceeds thisLoss of Sync Word Seconds Adding a Port-to-Port Cross Connection Configuring Cross ConnectionsDefault Mappings FieldPort B Adding a Slot-to-Slot Cross Connection SCP VPISlot SCP Card Configuring ATM Ports Configuring Traffic Profiles CdvtConfiguration Using the Web Interface June Location of ATM Line Card Information 1 Field Screen MonitoringWhat to Monitor Location of ATM Line Card Information 2 Field Screen LED is Indicating Front Panel LEDs Models 8955, 8965,Type Front Panel LEDs Model Diagnostics Lamp TestLoopback Test Model 8985 Only Maintenance Procedures Uploading and Downloading a Configuration Configuration FTP ParametersResetting the Configuration to Default Settings Resetting the Configuration to Downloaded SettingsFirmware Download Parameters Downloading and Switching FirmwareDownloading Firmware Switching Firmware Restarting the Line CardMaintenance Procedures June Connector Pins Port Tip, Ring Connector Pin Assignments8820 Telco Connector Pinouts Model 8968 Line Card Telco Connector Pinouts Connector Connector Pins Port Tip, RingTechnical Specifications Table B-1. ATM Line Card Technical Specifications 1 CriteriaTable B-1. ATM Line Card Technical Specifications 2 Criteria Index NumericsIN-2 IN-3 IN-4