Paradyne and 8985, 8968, 8965, 8955 manual Creating Alarm Threshold Profiles for Model

Page 22

3. Configuration Using the Web Interface

Creating Alarm Threshold Profiles for Model 8985

Procedure

To create an alarm threshold profile for an SHDSL line card:

1.Click on Create New Profile. The Alarm Threshold Profile Create screen appears.

2.Enter or select the following fields:

Field

Description

 

 

Profile Name

Specify a name for this alarm profile.

 

 

Loop Attenuation Threshold

Specify a loop attenuation alarm threshold of 0–127 dB.

 

An SNMP Loop Attenuation crossing trap message and a

 

TL1 autonomous message may be sent if the current loop

 

attenuation reaches or exceeds this threshold. A Loop

 

Attenuation alarm will also be declared when the current

 

Loop Attenuation exceeds this value. A value of 0 disables

 

event notifications for the condition.

 

 

SNR Margin

Specify an SNR Margin alarm threshold of 0–15 dB. An

 

SNMP Margin crossing trap message and a TL1

 

autonomous message may be sent if the current SNR

 

Margin reaches or drops below this threshold. An SNR

 

Margin alarm will also be declared when the current SNR

 

Margin has dropped below this value. A value of 0

 

disables event notifications for the condition.

 

 

Errored Seconds

Specify an ES threshold of 0–900 seconds. An SNMP ES

 

trap message and a TL1 autonomous message may be

 

sent if the number of ES events in a 15-minute interval

 

equals or exceeds the selected value. At most one SNMP

 

and one TL1 notification will be sent per interval per

 

device. A value of 0 disables event notifications for the

 

condition.

 

 

Severely-Errored Seconds

Specify an SES threshold of 0–900 seconds. An SNMP

 

SES trap message and a TL1 autonomous message may

 

be sent if the number of SES events in a 15-minute

 

interval equals or exceeds the selected value. At most one

 

SNMP and one TL1 notification will be sent per interval

 

per device. A value of 0 disables event notifications for the

 

condition.

 

 

Code Violations

Specify a Code Violations threshold of 0–900 seconds. An

 

SNMP code violations trap message and a TL1

 

autonomous message may be sent if the number of Code

 

Violations in a 15-minute interval equals or exceeds this

 

threshold. At most one SNMP and one TL1 notification will

 

be sent per interval per device. A value of 0 disables event

 

notifications for the condition.

 

 

3-10

June 2004

8900-A2-GB20-30

Image 22
Contents ATM Line Cards Copyright 2004 Paradyne Corporation All rights reserved Contents Connector Pin Assignments DiagnosticsMaintenance Procedures Technical Specifications IndexDocument Purpose and Intended Audience About This GuideDocument Summary Product-Related Documents Document Number Document TitleAbout the ATM Line Cards ATM Line CardsATM Features ATM Line Card FeaturesEndpoint Support Features Sample Network Configurations Endpoint with Voice InterfacesManagement Information Base MIB Support Snmp Management CapabilitiesSnmp Trap Support Introduction Accessing the SCP Card Web InterfaceLogging Into the Web Interface Help Button Ending a SessionIf you would like to configure Card using See Configuration Using the Web InterfaceConfiguring Spectrum Management OverviewConfiguring ReachDSL Ports Field DescriptionConfiguring Adsl Ports 8965 Disabled Power management is disabled Configuring Shdsl Ports Configuring Line Profiles 8955, 8965 Upstream / Far End ProfileCreating Line Profiles for Ports Configuring Alarm Threshold Profiles 8955, 8965 Downstream / Near End Alarm ProfileLoss of Signal Seconds Creating Alarm Threshold Profiles for Model Violations in a 15-minute interval equals or exceeds thisLoss of Sync Word Seconds Adding a Port-to-Port Cross Connection Configuring Cross ConnectionsDefault Mappings FieldPort B Adding a Slot-to-Slot Cross Connection SCP VPISlot SCP Card Configuring ATM Ports Configuring Traffic Profiles CdvtConfiguration Using the Web Interface June What to Monitor MonitoringLocation of ATM Line Card Information 1 Field Screen Location of ATM Line Card Information 2 Field Screen Type Front Panel LEDs Models 8955, 8965,LED is Indicating Front Panel LEDs Model Diagnostics Lamp TestLoopback Test Model 8985 Only Maintenance Procedures Uploading and Downloading a Configuration Configuration FTP ParametersResetting the Configuration to Default Settings Resetting the Configuration to Downloaded SettingsDownloading Firmware Downloading and Switching FirmwareFirmware Download Parameters Switching Firmware Restarting the Line CardMaintenance Procedures June 8820 Telco Connector Pinouts Connector Pin AssignmentsConnector Pins Port Tip, Ring Model 8968 Line Card Telco Connector Pinouts Connector Connector Pins Port Tip, RingTechnical Specifications Table B-1. ATM Line Card Technical Specifications 1 CriteriaTable B-1. ATM Line Card Technical Specifications 2 Criteria Index NumericsIN-2 IN-3 IN-4