Paradyne 8955, 8968, 8965, and 8985 manual Creating Line Profiles for Ports

Page 19

3. Configuration Using the Web Interface

3. Click on Apply.

Creating Line Profiles for Ports (8985)

Procedure

To create a line profile for SHDSL ports:

1.Click on Create New Profile. The SHDSL Profile Create screen appears.

2.Enter or select the following fields:

Field

Description

 

 

Profile Name

Specify a name for this line profile.

 

 

Max Rate

Enter a maximum rate from 192 to 2304 kbps.

 

 

Min Rate

Enter a minimum rate from 192 to 2304 kbps.

 

 

Mode

Select the regional setting supported, as specified by

 

ITU-T G.991.2:

 

Annex A

 

￿Annex B

 

Both

 

 

Remote Management

Select Enable or Disable from the drop-down list to

 

determine whether remote management is supported for

 

the network element this profile is assigned to.

 

 

Reference Clock

Select the timing source from the drop-down list:

 

System – Clocking is provided by the backplane. (The

 

backplane clock is configured on the Configuration -

 

￿System - Clocking screen.)

 

Local – Clocking is provided by an onboard oscillator.

 

 

Target Margin

Enter a target noise margin from 2–15 dBm, or None.

 

 

Interface

Select an interface from the drop-down list:

 

￿Wire Pair 1 – The profile applies to Wire Pair 1.

 

Wire Pair 2 – The profile applies to Wire Pair 2.

 

Select Wire Pair 1 if this profile is to be used for ports that

 

use only one wire pair.

 

 

3. Click on Apply.

8900-A2-GB20-30

June 2004

3-7

Image 19
Contents ATM Line Cards Copyright 2004 Paradyne Corporation All rights reserved Contents Technical Specifications Index DiagnosticsMaintenance Procedures Connector Pin AssignmentsDocument Purpose and Intended Audience About This GuideDocument Summary Document Number Document Title Product-Related DocumentsATM Line Cards About the ATM Line CardsATM Features ATM Line Card FeaturesEndpoint Support Features Endpoint with Voice Interfaces Sample Network ConfigurationsManagement Information Base MIB Support Snmp Management CapabilitiesSnmp Trap Support Introduction Accessing the SCP Card Web InterfaceLogging Into the Web Interface Ending a Session Help ButtonOverview Configuration Using the Web InterfaceConfiguring Spectrum Management If you would like to configure Card using SeeField Description Configuring ReachDSL PortsConfiguring Adsl Ports 8965 Disabled Power management is disabled Configuring Shdsl Ports Upstream / Far End Profile Configuring Line Profiles 8955, 8965Creating Line Profiles for Ports Downstream / Near End Alarm Profile Configuring Alarm Threshold Profiles 8955, 8965Loss of Signal Seconds Violations in a 15-minute interval equals or exceeds this Creating Alarm Threshold Profiles for ModelLoss of Sync Word Seconds Field Configuring Cross ConnectionsDefault Mappings Adding a Port-to-Port Cross ConnectionPort B SCP VPI Adding a Slot-to-Slot Cross ConnectionSlot SCP Card Configuring ATM Ports Cdvt Configuring Traffic ProfilesConfiguration Using the Web Interface June What to Monitor MonitoringLocation of ATM Line Card Information 1 Field Screen Location of ATM Line Card Information 2 Field Screen Type Front Panel LEDs Models 8955, 8965,LED is Indicating Front Panel LEDs Model Lamp Test DiagnosticsLoopback Test Model 8985 Only Maintenance Procedures Configuration FTP Parameters Uploading and Downloading a ConfigurationResetting the Configuration to Downloaded Settings Resetting the Configuration to Default SettingsDownloading Firmware Downloading and Switching FirmwareFirmware Download Parameters Restarting the Line Card Switching FirmwareMaintenance Procedures June 8820 Telco Connector Pinouts Connector Pin AssignmentsConnector Pins Port Tip, Ring Connector Connector Pins Port Tip, Ring Model 8968 Line Card Telco Connector PinoutsTable B-1. ATM Line Card Technical Specifications 1 Criteria Technical SpecificationsTable B-1. ATM Line Card Technical Specifications 2 Criteria Numerics IndexIN-2 IN-3 IN-4