D-Link DVG-2101S user manual How can I set my computer to use a static IP address?

Page 56

DVG-2101S User Manual

Frequently Asked Questions

Q: How can I set my computer to use a static IP address?

A:If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps below:

1.Windows® XP: Click on Start > Control Panel > Network Connections.

Windows® 2000: From the desktop, right-click My Network Places > Properties.

2.Right-click on the Local Area Connection which represents your network adapter and select Properties.

3.Highlight Internet Protocol (TCP/IP) and click Properties.

4.Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN IP address on your Adapter.

Example: If the Adapter’s LAN IP address is 192.168.1.150, make your IP address 192.168.1.x where x is a number between 1 and 254 but except (192.168.1.1 for example). Make sure that the number you choose is not in use on the network. Set Default Gateway the same as the LAN IP address of your DVG-2101S (192.168.1.150).

5.Click OK twice to save your settings.

Q:I get a dial tone, but when I dial any phone number I receive a busy signal.

A:The unit may not have been properly configured with the correct account information in the web-based utility.

1.Access the web-based utility by entering the IP address: 192.168.1.150 in the Address bar.

2.Select the Setup tab and click the SIP Account List submenu.

3.Enter the account information provided by your VoIP service provider, including Display Name, User Name, Authentication Name, Password, Proxy Server (if applicable), Outbound Proxy Server (if applicable), etc.

Q: After setting up the DVG-2101S, I cannot access the Internet.

A:Make sure that the Ethernet cable from the PC is plugged into the LAN port of broadband modem or router after you finish the configuration of the DVG-2101S.

Q: Can I use my DVG-2101S on a MGCP network?

A:No, DVG-2101S is a SIP device and uses the SIP protocol in handling all of the telephony elements.

54

Page 55 Page 57
Image 56
Page 55 Page 57
Contents DVG-2101S VoIP Telephone Adapter Table of Contents Package Contents IntroductionFeatures „ NTP„ VPN Power LED Front PanelPhone LED Register LEDReset Button Rear PanelHardware Installation Connecting the DVG-2101S Directly to a ModemConnecting the DVG-2101S Behind a Router Hardware Installation Configuration Enter or Return keyClick Setup Wizard StepStatic IP users have to set the DNS address Click Next Step Setup Internet SetupConnection Type Dynamic IPStatic IP Password Service NameName PPPoEMAC Address Clone CloneStatic Routing VoIP Setup SIP Account ListPhone Book NumberInternet Time Zone Enable Daylight Saving Dates Time and DateAdvanced VoIP SettingsCall Feature Examples of Making a Conference Call ScenarioSIP Setting Digit Plan Digit Plan Syntex To specify a Enter the following Result Component DescriptionDigits Input IVRDigit Map Scenario Rule Combination VoIP Adapter will do…Prefix ModeMin Len ExampleDial Prefix Codec PriorityCodec PacketizationPhone Setting DNS Server Address Host Name Username or Key Timeout StatusDynamic DNS QoS Dialing out Settings VPNLAN Mask System MaintenanceConfiguration Auto Provision Times Period FileSnmp for Snmp model only Log Setting Firmware Update Access Control Admin Current Password Admin NewPing Test Status Device InformationVoIP Status CDR Status VPN Status Network Status System Log Help Help MenuConfiguration through IVR Frequently Asked Questions Why can’t I access the web-based configuration utility?What can I do if I forgot my password? How can I check if my IP address is correct for logging in?How can I set my computer to use a static IP address? Can I use my DVG-2101S on a Mgcp network?Technical Specifications FCC EMI Statement FCC Caution
Top Page Image Contents