EFJohnson LTR 98xx, High Tier manual Miscellaneous

Page 48

MISCELLANEOUS

Out-Of-Range - If this tone sounds shortly after pressing the PTT switch and “OUT RNGE” is displayed, the transceiver was unable to contact a repeater. The usual cause for this is an out-of-range condition (see “Operation At Extended Range” on page 54). Once this tone sounds, no more access attempts are made until the PTT switch is released and then pressed again. This condition is not indicated with conventional operation.

Time-Out Timer - If this tone sounds after the transmitter has been keyed for an extended period and “TIMEOUT” is displayed, the trans- mitter has been disabled by the Time-Out Timer feature (see page 29). This tone sounds with both LTR and conventional operation. Ten seconds before this tone sounds, a single beep sounds to indicate that time-out will soon occur.

Transmit Inhibit - If this tone sounds as soon as the PTT switch is pressed with an LTR system selected and “TX INHIB” is displayed, the transmitter has been disabled by the Transmit Inhibit feature (see page 41).

Transmit Disable On Busy - If this tone sounds as soon as the push-to-talk switch is pressed with a conventional system selected and “DSBL BSY” is displayed, the channel is busy and the transmitter was disabled by the Transmit Disable On Busy feature (see page 44).

Receive-Only Channel - If this tone sounds as soon as the push-to-talk switch is pressed with a conventional system selected and “TX DSBL” is displayed, the channel is receive-only (see page 29).

Tx While Receiving Call - If the push-to-talk switch is pressed while receiving a LTR call, this tone sounds and “DSBL BSY” is displayed.

Proceed (Clear-To-Talk) Tone - This is a short tone which sounds after the push-to-talk switch is pressed to indicate when talking can begin (see page 28). A loud (two-pitch) tone may also be programmed.

Key Press Tone - This is a short tone that indicates when an option switch is pressed (all modes).

48

Image 48
Contents High Tier Operating Manual Page Page Safety Information FCC Exposure Limits Limits For General Population/Uncontrolled ExposureFrequency Whip Model No Base Model No Table of Contents Table of Contents Quick Reference Guide Features General FeaturesControls and Display Front Panel ControlsMicrophone Push-To-Talk PTT Switch Not Shown Push-button on Rear Panel Jacks and Connectors Display Description Power-Up Sequence Determining Volume LevelGeneral Operation Numeric Display Mode Alpha Tag Display ModeBacklight Operation System/Group Display InformationSelect Mode Indication With Numeric Display Select Mode Indication With Alpha Tag DisplaySelecting the System and Group Setting Squelch Control Standard Calls IntroductionPlacing a Standard Call LTR OperationConventional Operation Receiving a Standard CallTelephone Calls Placing Telephone CallsReceiving a Telephone Call General Features Landside-Originate CallsBank Select Call Indicator Emergency SwitchEncryption Encryption Indicator Function FCN SwitchHome System/Group Select Horn AlertPower Turn-Off Delay Option SelectProceed Clear-To-Talk Tone Stealth Mode Time-Out TimerReceive-Only Groups Option Switches and Menu Mode Option SwitchesTone Select Transmitter Thermal FoldbackMenu Mode and Option Switch Functions SwitchMenu Mode Introduction Using Menu ModeSystem and Group Scan System and Group Scan Scan List Programming Scan Delay and Continue Timers Transmitting In The Scan ModeSystem and Group Scan LTR and Conventional Modes GeneralMonitoring Conventional Channels Before Transmitting LTR Features Standard and Telephone CallsCalls on Priority and Block ID Codes Transmit Inhibit Busy Queuing System SearchTranspond Conventional Features Monitor ModeTransmit Disable On Busy Talk-Around Call Guard Squelch Priority Group SamplingMiscellaneous Supervisory TonesMiscellaneous LTR Telephone Call Tones Display Messages Miscellaneous Menu Mode Messages Bright DIM OFFSystem Operator Programming Speaking Into MicrophonePreventing Battery Discharge Operation At Extended RangeLicensing Transceiver Service