Cobra Electronics CXR725 After 10 seconds of inactivity, unit starts scan again, Current setting

Page 14
VibrAlert and Call Alert

Operation

Mode Functions

 

 

 

 

 

 

 

Introduction

Operation

Customer Assistance

Warranty

 

During memory location scan (while receiving an Incoming trans- mission), you can choose from the following:

a. Press and hold the Talk button to communicate on that memory location.

b. Your radio will remain on that memory location and return to Standby mode. Press the Channel Up or Channel Down button to resume scanning memory locations.

c. After 10 seconds of inactivity, unit starts scan again.

If you press the Talk button while scanning, but more than 10 seconds after receiving a transmission, you will transmit on the memory location on which, during scanning, you last received a transmission.

If you do not press any button within 10 seconds, your radio will automatically resume scanning memory locations.

During memory location scan (while not receiving a transmission), you can choose from the following:

a. Press and hold the Talk button to communicate on the channel/privacy code that was displayed before you entered mode functions or memory location on which, during scanning, you last received a transmission.

b. Press the Mode button to proceed to other functions.

c. Press the Lock/Enter button to return to Standby mode on the channel/privacy code that was displayed before you entered mode functions or the memory location on which, during scanning, you last received a transmission.

To reduce the number of memory locations being scanned, you may de-program any unwanted locations. (See page 16 to de-program a memory location.)

Your microTALK radio can alert you to incoming signals by sounding an• audible call tone, by vibrating silently or both.

Mode Button

To change call settings:

VibrAlert + Ring

 

 

1. Press the Mode button

 

 

until the Call Setting icon

 

 

flashes on the display.

 

Channel Buttons

The current setting (“01”

VibrAlert Only

vibrate + ring, “02” vibrate

 

 

 

 

only or “03” ring only)

 

 

is displayed.

 

 

2. Press the Channel Up or

 

 

Channel Down button to

Ring Only

 

change the call setting.

 

3. Choose one of the following:

a. Press the Mode button to enter the new setting and proceed to other functions.

b. Press the Lock/Enter button to enter the new setting and return to

Standby mode.

22

Nothing Comes Close to a Cobra® 23

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Automated Help Desk Making Life Easier and SaferRadio while on the go QuestionsFeatures Product FeaturesWarranty and Trademark AcknowledgementCaring for Your microTALK Radio Avoid exposure to extreme temperaturesReplace battery compartment cover and belt clip Estimated operation time on full charge 10 hoursUsing Your Radio Turning on Your microTALK RadioListening for a Response Selectable HighLow Power OutputChannels To Illuminate DisplaySpeaker/Microphone/Charge Jack Signal Strength MeterAuto Squelch/Maximum Range MicroTALK RangeWill be displayed in the following order Mode FunctionsScrolling through Mode Functions Privacy CodesSet DCS Privacy Codes To select a DCS privacy code Set Ctcss Privacy Codes To select a Ctcss privacy codeAfter selecting a channel, press Voice Activated Transmit VOX Memory LocationsTo recall a stored memory channel location Entered mode functionsPress the Mode button to enter the channel/privacy To next Memory location, which will blinkChannel Scan To scan privacy codes Return to Standby modeIf you press the Talk button while scanning, but more than Memory Location Scan Press the Mode button Press the Mode button to proceed to other functionsTo change call settings Current settingTime you press a button or change a setting Mode Functions and General SpecificationsCall Tone Settings Unique call alert Keystroke TonesNormal Position General Specifications FCC LicenseSafety Information for microTALK Radios For Products Purchased in the U.S.A Product ServiceSend the entire product For Products Purchased Outside the U.S.A
Top Page Image Contents