Uniden EXS 9995 manual Direct wall mounting

Page 9

Before you plug the other end of the telephone cord into the modular jack on the wall, charge the battery (See Charging the Battery Pack, page 9).

Be careful not to insert the mounting screws into possible electrical hazards such as cables, wiring,

or pipes.

7. On the base unit, pull the handset retainer out of the slot. Rotate it clockwise 180 degrees.

8. Flip the retainer from front to back. Slide it back into the slot so that the lip of the retainer is up and the ▼ is down. The retainer holds the handset in place.

▼Direct wall mounting

If you don’t have a standard wall plate, you can mount your phone directly to the wall. Before doing this, consider the following:

•Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting the screws into the wall.

•Mount your phone near a working phone jack to avoid excessive cord lengths.

•Make sure the wall material is capable of supporting the weight of the base and the handset.

1.Insert two #10 mounting screws (with 1-3/8 inches minimum length and the appropriate anchoring

device) into the wall 3-15/16 inches apart. Allow about 3/16 of an inch between the wall and screw heads for mounting the phone.

2. Refer to steps 1 through 8 on page 6 and 7 to mount the telephone.

7

Image 9

Contents Page Controls and Functions Contents Welcome FeaturesIncluded in Your Package Selecting a Location Switch to interrupt its powerDESK/TABLETOP Installation Standard wall plate mounting Wall InstallationDirect wall mounting Installing the Handset Battery Pack Initial battery charging Charging the Battery PackCharging optional battery packs Pull the cover of battery chargerCleaning the Battery Contacts Setting the PULSE/TONE SwitchLow battery indicator Adjusting the Volume Controls To attach the beltclip Installing the BeltclipTo remove the beltclip Pull both side of the tabs from the holesTo reset the digital security code Headset InstallationAutomatic Digital Code Security Wait for 5 secondsBasic 2-line operation Making and Receiving CallsAnswering a Call from the Base When you finish the call, press line 1 to hang upMaking a Call from the Handset Dialing from Talk ModeHandset rings and the following Screen appears Pick up the handset Press lineUsing the Tone Feature Dialing from Standby ModeFlash and Call Waiting Using Redial Placing a Call on HoldTo redial from the handset Using the Mute Feature Using the page FeatureHandset beeps for 60 seconds Following screen appears Extension In Use Line OperationWAY Conferencing Press call id/hold Using Your EXS 9995 Intercom From the Base to the HandsetPress page/int’com on the base From Handset to Base Transferring a CallOn the handset, Press line 1 to talk Traveling OUT-OF-RANGEOn the Handset Storing a Phone Number in MemoryWhen you have finished entering a name, press select Editing a Phone Number in Memory Store Number Erasing a Number from Memory After erasing a number, you may add a new address to memoryFrom the Handset Page Using Memory Dialing Standby Mode Dialing from the HandsetPress line 1. The number dials Number dials Talk Mode Dialing from the HandsetSetting up Caller ID options Using Caller IDTo change your Caller ID options Turning AutoTalk and Caller ID/Call Waiting On or OffScreening Your Calls Programming Your Area CodeReviewing Caller ID name/numbers Line Select. The following screen appears Storing a Caller ID number in a memory locationTo delete a single Caller ID message, follow the steps below Deleting a Caller ID messagePress del/conf to delete name/numbers Deleting all Caller ID name/numbersUsing Cidcw Caller ID with Call Waiting Setting UP Your Answering System Turning the answering system on/offPress and hold clock until a tone sounds Setting Your Greeting Prerecorded GreetingRecording your Personal/User Greeting Press greeting to play the current greeting Choosing between Prerecorded and User GreetingsAnnounce only feature Selecting a PIN CodeLine 1 and line 2 must use the same PIN code Ring time switch is common for line 1 and line Setting Ring Rime SwitchPlaying your messages Using Your Answering SystemRepeating a Message Skipping a MessagePress skip at any time to skip to the next message Voice Memo Deleting a MessageDeleting individual message Deleting all messagesTo stop the recording, press voice memo or play/stop Recording a ConversationRemote Access Away from Home Remote Rome Monitor Quick Reference Chart Make sure you are using the correct PIN code Adjust the speaker volume on the baseCall-in features from Call-in featuresMemo Memo At Uniden, we’ll take care of you