Chapter 7 Global Meter Setup
7.2GROUP 0, FUNCTION 1 - THE METER ADDRESS
METER ADDRESS: Identifies the meter when communicating with a computer system or an RS485 bus. When numerous meters are at one site, it is essential that each meter have its own address.
ÖTo change the METER ADDRESS, follow these steps:
NOTE: PRESS MAX/MIN/LIMITS, AT ANY TIME, TO CANCEL BEFORE STORING THE LAST DIGIT OR SWITCH.
AC VOLTS
0. AI BI CI AI BI CI N N N B C A
AC AMPS
A B C N
MAX | MIN |
| LM1 LM2 | |||
|
|
|
|
|
|
|
AC VOLTS
0 | I. | A B C A B C |
| |||||||
I I I I I I |
| |||||||||
N N N B C A |
| |||||||||
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 00 I | AC AMPS |
| ||||
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
| A B C N |
| |
|
|
|
|
|
|
|
|
|
|
|
MAX MIN |
| LM1 LM2 |
| |||||||
|
|
|
|
|
|
|
|
|
|
|
MAX/MIN PRINT LIMITS PROG
VOLTS AMPS
PHASE
NEXT
MAX/MIN PRINT LIMITS PROG
VOLTS AMPS
PHASE NEXT
Step 1:
a.Enter Group Level of Programming Mode, (see Chapter 10).
b.Press MAX/MIN/LIMITS until 0. appears in upper display.
c.Press VOLTS to activate the GROUP.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 I |
| AC VOLTS |
| ||||
|
|
|
|
|
|
|
| A B C A B C |
| |||||
|
|
|
|
|
|
|
|
|
|
| I I I I | I I |
| |
|
|
|
|
|
|
|
|
|
|
| N N N B C A |
| ||
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
| |||||||||
| 02 _ |
| AC AMPS |
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
| A B C N |
| |
|
| MAX MIN |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
| LM1 | LM2 |
| ||||||
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| MAX/MIN | VOLTS |
| AMPS | PHASE |
|
|
| |||
|
|
|
| LIMITS | PROG |
| NEXT |
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Ö01. appears in upper display.
ÖLower display indicates the current Meter Address.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 I. |
| AC VOLTS |
| ||||
|
|
|
|
|
|
|
| A B C A B C |
| |||||
|
|
|
|
|
|
|
|
|
|
| I I I | I I I |
| |
|
|
|
|
|
|
|
|
|
|
| N N N B C A |
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| 020 |
| AC AMPS |
| ||||
|
|
|
|
|
|
|
|
|
|
|
| A B C N |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| LM2 |
| |||||
|
| MAX MIN |
|
|
|
| LM1 |
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
| MAX/MIN | VOLTS |
| AMPS | PHASE |
|
|
| |||
|
|
|
| LIMITS | PROG |
| NEXT |
|
|
| ||||
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Step 2:
a.Press VOLTS to activate Data Entry Sequence.
ÖThree dashes appear in lower display.
b. Press PRINT/PROG for desired number.
• Press PRINT/PROG once and the blank signifies a zero.
• Press PRINT/PROG twice and 1 appears.
c.Press VOLTS to store.
ÖRepeat this procedure until new Address is entered.
ÖWhen complete, lower display indicates new Address.
See Chapter 12 to Exit.
7.3GROUP 0, FUNCTION 2 - COMMUNICATION BAUD RATE
BAUD RATE: Speed at which data is transmitted between device and remote computer. The rate programmed into the meter must match the rate used by the remote polling device.
Valid Baud Rates are 1200, 2400 and 4800. When entering a baud rate, the last zero is omitted. Therefore, three digits and a leading zero (or blank) must be entered. Example: To enter a baud rate of 2400, enter 0240.
ÖTo change the COMMUNICATION BAUD RATE, follow these steps:
NOTE: PRESS MAX/MIN/LIMITS, AT ANY TIME, TO CANCEL BEFORE STORING THE LAST DIGIT OR SWITCH.
23
GE Industrial Services