Display at position a Operation in progress

ON-SCREEN DISPLAY	– Status display –		(continued)
3 2 K C H – 1 / 2	S P 0 0 0 m i n	5

ON-SCREEN DISPLAY – Event display –

Event display : When a specific function is in activation or when the operation status is changed with the remote controller, etc, the events will be displayed at the positions shown below.

0 4	/ 0 1	/ 0 2		S T A N D B Y			-	O F F	4
1 1	: 2 0	: 0 0	T C R	0 2	: 0 0	: 0 0		: 0 0
				3

3 2 K		C H – 1		/ 2		S P	0 0 0 m i n
A			B L A N K		S E A R C H
B			I N D E X		D E T E C T E D
0 4	/	0 1	/ 0 2			S T A N D B Y - O F F
1 1	:	2 0	: 0 0	T C R		0 2 : 0 0	: 0 0 : 0 0

Display	Contents
AUDIO OUT	The standard level of the
LEVEL NORM	playback or EE audio level is
AUDIO OUT	set to NORMAL or ATT with
AUDIO OUT	the remote controller.
LEVEL ATT
AUDIO OUT CH-1/2	The playback audio channel is
AUDIO OUT CH-3/4	set to CH1/2, CH3/4 or MIX
AUDIO OUT CH-3/4	with the remote controller.
AUDIO OUT MIX

No.

Item

3	Time code

Content

•It displays the time codes (hour, minute, second and frame).

During playback, the time codes recorded on the tape are displayed.

Display at position A

...Operation in progress

DISPLAY ON

The on-screen display is turned on with the remote controller.

TCR	: time code reader data
TCG	: time code generator data
DTCG : time code data input from a DV IN terminal

•The symbols for the second and frame differ according to the framing modes. (NTSC only)

: 00

¥ dot (.) is used for a dropped frame.

colon (:) is used for a non-dropped

frame.

Display BLANK SEARCH INDEX + 1

INDEX MARK

Contents Blank search in progress.

Index search in progress. The number indicates the index search position.

When an index is written on the tape during recording.

DISPLAY AUTO

DISPLAY OFF

The on-screen display is set to AUTO with the remote controller. In the AUTO mode, the on-screen display is shown for about 4 seconds between mode switches.

The on-screen display is set to OFF with the remote con- troller.

• The time code display position can be set via the COUNTER

POSI. item of the DISPLAY menu.

• The TIME CODE item can be set to turn on/off the time code

display.

Display at position B

...Display for about 3 seconds

FIELD STEP	Field by field advance play-
	back is selected with the re-
	mote controller.

4	VTR operation mode

5	Remaining tape
	Remaining tape
	Memo
	If the display position of the time
	code is set to the upper right,
	this item will be displayed on the
	lower right

• The user’s bit is not displayed.

It displays the VTR operation modes, including: PLAY, EJECT, FF, REW, STANDBY-ON, STANDBY-OFF, STILL, REC, REC PAUSE, A. DUB, A. DUB PAUSE, SHTL (shuttle search), JOG (F.ADV, R.ADV), BLANK SRH (blank search), NO CASSETTE (cassette not loaded), OPERATE OFF.

When SHTL or JOG is displayed, the speed will also be dis- played at the same time.

•The VTR MODE item of the DISPLAY menu can be set to turn on/off the VTR operation mode display.

It displays the remaining tape duration (minutes). If it is not identified, “ – – – ” is displayed.

•The TAPE REMAIN item in the DISPLAY menu can be set to turn on/off the remaining tape duration display.

•The SP display disappears when the DVCAM cassette is being played back.

•Please use the remaining tape time as a gauge.

Display	Contents
INDEX DETECTED	Index is found during an in-
	dex repeat operation.
VIDEO END	Video end is found during a
DETECTED	video end repeat operation.
AUDIO MUTING	Audio is muted with the re-
ON	mote controller.
AUDIO MUTING	Audio is de-muted with the
OFF	remote controller.

1ST FIELD STILL

2ND FIELD STILL

FRAME STILL

When still or frame advance playback is selected with the remote controller, the type of still image is displayed.

•1st FIELD STILL

•2nd FIELD STILL

•FRAME STILL

– Status display –