JVC BR-DV3000U DUB Inhibit 48K DUB Inhibit LP, DUB Inhibit DV, Head Cleaning Required Overheating

Page 13

ON-SCREEN DISPLAY Alarm display

Alarm display : Alarm messages are displayed as shown below, when an operation error has occurred or when the unit is in a poor condition for operation. E.g., dirty head.

 

3 2 K

C H – 1 /

2

 

 

S P

0 0 0 m i n

A

H E A D

C L E A N I

N G

 

R E Q U I

R E D !

B

 

 

 

N O

D V

S

I

G N A L

 

 

 

 

 

 

0 4

/ 0 1

/ 0 2

 

 

 

S T A N D B Y - O F

 

F 1 1

: 2 0

: 0 0

 

T C R

0 2 : 0 0 : 0 0 : 0

Display at position A : Displays which show the state of the unit (and which are not set

via the DISPLAY mode) continues to be displayed here until the conditions are rectified.

Display COPY INHIBIT REC INHIBIT

A. DUB INHIBIT (REC TAB)

A. DUB INHIBIT (48K)

A. DUB INHIBIT (LP)

A. DUB INHIBIT (BLANK)

A. DUB INHIBIT (DV)

Contents The user attempts to record signals protected with the copy guard.

The user attempts to record on a write protected cassette tape. (The rear slide is pushed to SAVE.)

The user attempts to perform audio dubbing on a write protected cassette tape. (The rear slide is pushed to SAVE.)

This message is displayed when audio dubbing is attempted under the following con- ditions:

The AUDIO MODE item of the AUDIO/VIDEO menu is set to 48k.

The tape is recorded with a sample frequency of 48kHz.

The user attempts to perform audio dubbing on a tape recorded in the LP mode.

The user attempts to perform audio dubbing on a blank tape.

The user attempts to perform audio dubbing during DV signal input. (The INPUT SEL switch is set to DV)

Display LOW VOLTAGE

HEAD CLEANING REQUIRED!

OVERHEATING!

Contents

The voltage of the DC input power is low. Continued operation will bring the unit to the Operate OFF mode.

The video head is dirty. Please clean it with the dedicated head-cleaning tape. (Page 8) If the head is clogged, it will be detected in the PLAYBACK mode and displayed. When the unit enters the STOP mode or the cassette is ejected, the display goes off.

The temperature inside the unit has exceeded the regulated value. Please disconnect the power and place the unit in a cool place. If this message is displayed again, dam- age may have occurred. Please consult with your JVC-authorized service agent.

A. DUB INHIBIT (NTSC/PAL)

A. DUB INHIBIT (DVCAM)

OPERATION LOCK

This message is displayed when the signal system is changed during audio dubbing (NTSC or PAL).

The user attempts to perform audio dubbing on a DVCAM format tape.

This message is displayed when a button on the unit is pressed while the OPERA- TION LOCK function is engaged (ie, the OPERATION item of the SYSTEM (2/2) menu is set as ON).

Warning display : When anomalies occur in the VTR, warning messages with error codes will be displayed.

Display at position B : Messages indicating operation errors are displayed for about 3 seconds.

They are displayed when the DISPLAY mode is ON or AUTO.

3 2 K

C H – 1

/ 2

S P 0 0 0 m i n

Display INVALID TAPE!

LP TAPE!

Contents

Data tapes for PC use or DVC PRO tapes has been inserted. The cassette will be ejected.

The user attempts to play back a tape recorded in the LP mode. This unit cannot record or play in the LP mode.

 

 

W

 

D R U M

0 4

/ 0 1

/ 0 2

1 1

: 2 0

: 0 0

A R N I N G M O T O R

T C R

7 0 0

1

F A I

L U R E

S T A N D B Y

0 2 :

0 0 : 0

 

 

Warning display

 

 

 

 

For details, please

 

 

refer to page 66,

 

 

“Warning Display”.

- O F F

0

: 0 0

 

NO DV SIGNAL

The user attempts to record without DV signal input.

22

23

Image 13
Contents BR-DV3000U Port Cable SupplementImportant In the United Kingdom For Your Safety AustraliaMains Supply AC 230 V ` Table of Contents Daily maintenance and regular inspection PrecautionsPrecautions on the use of tape Introduction Precautions on the use of cleaning tapeCassette tape CondensationFront panel REC Record button/LED FF Fast forward button/LED Indicator Audio indicatorPlay Play button/LED @ Stop Stop button/LEDRear panel ADV button Still Mode buttonREV button Operate button fMemo On-screen display Contents Method Display at position a Operation in progress Content Display at position B Display for about 3 seconds No DV Signal Head Cleaning Required OverheatingDUB Inhibit 48K DUB Inhibit LP DUB Inhibit DV Operable scope of the wireless remote controller Precautions on the use of batteryLoad in 2 batteries Close the cover Model onlyTurning off the power PowerConnecting to the AC adapter Switching on the powerSelecting the NTSC/PAL signal system Operation Lock modeEjecting the cassette Setting the date and timeEnabling on-screen display Setting/displaying date and timeSetting Recording Connection and settingConnection Preset time codes Setting time codesTime code recording Recording time codes of a DV input terminalRecording method Recording index signalsRecording Audio dubbing Backup recording function Connection/setting Special playback function Basic playback methodFast forward/rewind Frame advance reverse playbackLocate function Special playbackVariable speed playback Index searchRepeat playback Repeat Mode item of the System 1/2 menuRepeat operation Ginning Press the Play button to begin replayPlayback signals Setting the TC Adjust item of the Time Code menuApplicable model Panel to 9 PINPanel can be set at any position Remote FF/REW ModeRemote Display the menu for setting Set the unit to the Stop modeDisplay the TOP Menu Contents of the menus Contents of the menus  Remote 2/2 menu Items Setting Display 1/2 menu Model  Display 2/2 menu Alarm  Warning display Displayed regardless of the Display modeRemote controller Main unit Press the Menu button  To set the unit to the Stop modePower is not supplied even when To return to the usual screen Diagram of external dimension Unit mm