JVC BR-DV3000U Recording method, Recording Audio dubbing, Recording index signals

RECORDING – Recording method –

RECORDING – Audio dubbing –

Remote controller

	3.		2.
PAUSE button			REC button
2. 4.	A.DUB	PAUSE	REC
PLAY	F.REV	PLAY	F.ADV
button
	REW		FF
5.		STOP
STOP	INDEX–		INDEX+
button	REMOTE CONTROL UNIT
		RM-G3000
Memo
• If recording has been
paused for an extended pe-
riod of time, the unit will au-
tomatically		go	into the
STOP mode to protect the
tape. The time period after
the lapse of which the unit
will enter the STOP mode
can be configured via the
LONG PAUSE TIME item of
the SYSTEM (1/2) menu.
• This unit cannot perform
editing functions.

Main unit

		2.	2. 4.
		REC	PLAY
		button	button
OPERATE				EJECT
				MENIU
Mini	A.DUB	REC	PLAY	PAUSE
		DVCAM NTSC PAL REC INH.			3.
PROFESSIONAL		CH-1/3
				SET	PAUSE
MIC REMOTE SEL.	INPUT SEL.	REW	STOP	FF
SERIAL	LINE	CH-2/4			button

9PIN	WIRELESS	DV	Y/C	BR-DV3000
				5.	STOP button

1.	Load the cassette.
• Before loading the cassette, please check that the rear slide of
	the cassette is pushed to REC.
	¥ The Main unit is powered on.

2.	Start recording.
•	Hold down the REC button and press the PLAY button.
3.	Pause recording.
•	Press the PAUSE button.
4.	Resume recording.
•	Press the PLAY button.
5.	Stop recording.
•	Press the STOP button.

For tapes recorded in the 32kHz audio mode, audio dubbing can be performed on the CH3 and CH4 channel after the recording. (After-recording)

Notes

•For tapes recorded in the 48kHz audio mode, audio dubbing cannot be performed.

•Audio dubbing cannot be performed for DV input signals.

3.

2.

3.

3. A.DUB button

1. 4.

A.DUB

PLAY button

PAUSE button

button

1. 4.

A.DUB

PAUSE

REC

OPERATE

EJECT

F.REV

F.ADV

PLAY

PLAY

button

MENIU

REW

FF

5.

Mini

A.DUB

REC

PLAY

PAUSE

STOP

DVCAM NTSC PAL

REC INH.

2. 3.

PROFESSIONAL

STOP

INDEX–

INDEX+

CH-1/3

SET

PAUSE

REMOTE CONTROL UNIT

MIC

REMOTE SEL.

INPUT SEL.

CH-2/4

REW

STOP

FF

button

SERIAL

LINE

button

RM-G3000

9PIN

WIRELESS

DV Y/C

BR-DV3000

MIC

INPUT SEL switch

5. STOP button

terminal

Connection

Memo

• During audio dubbing, if the tape comes to a

Audio dubbing sounds are input from the AUDIO IN

part recorded in a non dubbing-feasible mode

(such as LP mode or 48kHz audio mode), the

terminal on the rear panel or the MIC terminal on

VTR will enter the STOP mode. When this hap-

the front panel. MIC terminal prevail over the AU-

pens, high-volume noise from the DV output

DIO IN terminal.

will occur. Hence, before audio-dubbing, please

Setting

check the recording mode of the tape.

• In the case that a microphone is connected to

•

Set the AUDIO item of the AUDIO/VIDEO menu

the MIC terminal, sound output from this ter-

minal will be recorded. In the absence of MIC

to 32k.

•

input, signals from the CH1/3, CH2/4 AUDIO

Do not set the INPUT SEL switch on the front

IN terminal on the rear panel will be recorded.

panel to DV.

• When audio dubbing cannot be performed, an

Operation

alarm message will be displayed on the moni-

tor. ( ☞ Page 23)

Memo

If recording is executed right after the RECORDING PAUSE state, index signals will not be recorded.

Recording index signals

When the INDEX WRITE item of the SYSTEM (1/2) menu is set as ON, an index signal is recorded at the starting position of recording. In the PLAYBACK mode, the position where the index signal is recorded can be detected. (Index search)

⬛During recording, please press the REC button to record the index signal.

*Please allow at least an interval of 1 minute between recording of index signals.

Recording of index signals after tape recording is not possible.

1.		• Audio dubbing PAUSE cannot be executed di-
	Press the PLAY button to play the tape.	rectly in the STOP mode. Please execute it in
		the STILL mode.
2.
	At the position where you want to au-	During audio dubbing pause, sound from the
	dio dub, press the PAUSE button.	CH3/CH4 channel is output via the monitor but
	¥ The unit goes into the STILL mode.	sound output from the DV terminal is not pos-
3.		sible.
	Hold down the PAUSE button and press
		• If audio dubbing is repeated on a short section
	the A.DUB button.	of the tape, noise may occur for an instant when
	¥The unit goes into the audio dubbing pause	the section is played.
		• During audio dubbing, noise may be produced
	mode.
4.		on the playback video or EE sound but the re-
	Press the PLAY button.	cording is normal.
		• The playback sound of CH1/2 cannot be re-
	¥ Audio dubbing begins. Audio signals are
	recorded on the CH3 and CH4 channel.	corded on CH3/4 (sound on sound).
		• During backspace operation of audio dubbing,
⬛To stop audio dubbing temporarily, press		audio dubbing cannot be performed on unre-
the PAUSE button.		corded parts.
		• When audio dubbing is performed on tapes re-
5.
	To end audio dubbing, press the STOP	corded on other devices, it may not record cor-
		rectly. Please record with this unit before per-
	button.
		forming audio dubbing.

38

39