Goodman Mfg CPG SERIES installation manual 240/1/60 0140L00429 REV B

CPG0060*1D SINGLE PHASE 240V/60HZ DIRECT DRIVE

HIGH VOLTAGE!

DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO

DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

L1		SUPPLY VOLTAGE					L2
		240/1/60
C T1	R					C	L2
	C		H	C
	S
			C		CM
L	N				VMR
	EM
				3	1	VM
	3	2	1
L1 NOTE 6	TB1		TR		NOTE 6
				TB1			L2
	FS	IGN	FS				IIC
F
	C
					EM	C
	H
	D1
4		LS	VMR			TB1
5

COMPONENT LEGEND

ALS	AUXILIARY LIMIT SWITCH
COMP	COMPRESSOR
CM	CONDENSER MOTOR
C	CONTACTOR
EM	EVAPORATOR MOTOR
F	FUSE
FS	FLAME SENSOR
GND	EQUIPMENT GROUND
GV	GAS VALVE
HPS	HIGH PRESSURE SWITCH
IIC	INTEGRATED IGNITION CONTROL
IGN	IGNITOR
LPS	LOW PRESSURE SWITCH
LS	LIMIT SWITCH
PLF	FEMALE PLUG/CONNECTOR
PS	PRESSURE SWITCH
RCCF	RUN CAPACITOR FOR COMPRESSOR/FAN
RS	ROLLOUT SWITCH
TB1	TERMINAL BLOCK (24V SIGNAL)
TR	TRANSFORMER
VM	VENT MOTOR
VMR	VENT MOTOR RELAY

NOTES

1. REPLACEMENT WIRE MUST BE THE SAME

SIZE AND TYPE OF INSULATION AS ORIGINAL.

(USE COPPER CONDUCTOR ONLY).

			FACTORY WIRING
			LINE VOLTAGE
			LOW VOLTAGE
			OPTIONAL
			HIGH VOLTAGE
			FIELD WIRING
			HIGH VOLTAGE
			LOW VOLTAGE
			WIRE CODE
BK	BLACK
BL	BLUE
BR		BROWN
GR		GREEN
OR		ORANGE
PK	PINK
PU		PURPLE
RD		RED
WH		WHITE
YL	YELLOW

BL/PK BLUE WITH PINK STRIP YL/PK YELLOW WITH PINK STRIP

	IIC	3		ALS	RS
		6		PS
		8
9	7	10		12
				11
				LPS	HPS
R	G	W1	W2	Y1	Y
					Y2
TO THERMOSTAT
TERMINAL BLOCK

GV
C
NOTE		6	5	4
4	PLF
		3	2	1
TB1
	C

2. FOR 208 VOLT TRANSFORMER OPERATION

MOVE BLACK WIRE FROM TERMINAL 3 TO

TERMINAL 2 ON TRANSFORMER.

3. FOR DIFFERENT THAN FACTORY SPEED TAP.

CHANGE COOLING SPEED AT MOTOR T4 AND

T5 TERMINALS. CHANGE HEATING SPEED AT

MOTOR T1. T2, AND T3 TERMINALS

COOLING SPEED (YELLOW WIRE)

T3 - LOW SPEED

T4 - HIGH SPEED

HEATING SPEED (WHITE WIRE)

T1 - LOW SPEED (070)

T2 - MED. SPEED

T5 - HIGH SPEED (140)

4. ACCESSORY ECONOMIZER PLUG ADJACENT

TO BLOWER HOUSING IN RETURN AIR

COMPARTMENT. REMOVE MALE PLUG AND

THERMOSTAT

FIELD WIRING

	NO ECONOMIZER
W	WH	W
G	GR	G
R	RD	R
Y1
Y/Y2	YL	Y
C	BL	C
TB1		STAT
WITH ECONOMIZER OPTION

INSTALLER/SERVICEMAN

STATUS LIGHT	EQUIP. STATUS					CHECK
ON	NORMAL OPERATION		-
OFF	NO POWER OR
	INTERNAL CONTROL
	FAULT
1 BLINK	IGNITION FAILURE					GAS FLOW
		OR		GAS PRESSURE
	OPEN ROLLOUT				GAS VALVE
	SWITCH			FLAME SENSOR
		OR		FLAME ROLLOUT
	OPEN AUX. LIMIT				BAD SWITCH
	SWITCH			AUX. LIMIT OPEN
2 BLINKS	PRESSURE SWITCH					CHECK
		OPEN	PRESSURE SWITCH
3 BLINKS						CHECK
	WITHOUT INDUCER ON		PRESSURE SWITCH
4 BLINKS	OPEN LIMIT SWITCH			MAIN LIMIT OPEN
					BAD SWITCH
5 BLINKS	FALSE FLAME SENSED
6 BLINKS	COMPRESSOR			3 MIN. COMP.
	OUTPUT DELAY

ATTACH FEMALE PLUG TO ECONOMIZER

ACCESSORY.

5. USE COPPER CONDUCTORS ONLY.

USE NEC CLASS 2 WIRE.

6.L1 AND L2 ON ICC CONTROL IS 24V INPUT.

7.SPEED TAP TERMINATIONS SHOWN ON DIAGRAM ARE REPRESENTATIVE, BUT

ACTUAL FACTORY SETTINGS MAY BE DIFFERENT BASED ON THE HEATING VALUE OF THE UNIT.

8.FOR LOW STAGE OPERATION ONLY, REMOVE WHITE JUMPER. FOR 2 STAGE OPERATION, REMOVE JUMPER AND CONNECT W2 TO W2 ON THERMOSTAT.

SEE UNIT RATING PLATE FOR TYPE AND SIZE OF OVER

CURRENT PROTECTION .

240/1/60 0140L00429 REV B

W	WH	W
G	GR	G
R	RD	R
Y1	YL	Y
Y/Y2
C	BL	C
TB1		STAT
2 STAGE COOLING
W	WH	W
G	GR	G
R	RD	R
Y1	YL	Y1
Y/Y2	PK	Y2
C	BL	C
TB1		STAT

Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.

41