Goodman Mfg CPG SERIES installation manual 208-240/3/60 0140L00979 REV a

CPG036(048)0453B THREE PHASE 240V/60HZ BELT DRIVE

HIGH VOLTAGE!

DISCONNECT ALL POWER BEFORE SERVICING OR INSTALLING THIS UNIT. MULTIPLE POWER SOURCES MAY BE PRESENT. FAILURE TO

DO SO MAY CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH.

L1				SUPPLY VOLTAGE				L2	L3
				208-240/3/60
C	T1		T2		T2		C
			T1
			T3			T3	C
				FC
						CM
						BC
BC	EM					BC
						1	VMR VM
				1		3
NOTE 3						TR	NOTE 3
						IGN	BC		IIC
F			FS			FS
	H	C
			D1
4				LS		VMR
5
				ALS		RS
IIC		3					GV
		6
				PS
		8
9	7	10	12
			11				C
				LPS	HPS
							NOTE 2	6	5	4
							PLF
				Y				3	2	1
R	G	W	Y1			C
				Y2

INSTALLER/SERVICEMAN

STATUS LIGHT	EQUIP. STATUS					CHECK
ON	NORMAL OPERATION		-
OFF	NO POWER OR
	INTERNAL CONTROL
1 BLINK	IGNITION FAILURE					GAS FLOW
				GAS PRESSURE
	OPEN ROLLOUT					GAS VALVE
	SWITCH			FLAME SENSOR
	OPEN AUX. LIMIT			FLAME ROLLOUT
					BAD SWITCH
	SWITCH			AUX. LIMIT OPEN
2 BLINKS	PRESSURE SWITCH					CHECK
		OPEN	PRESSURE SWITCH
3 BLINKS						CHECK
	WITHOUT INDUCER ON		PRESSURE SWITCH
4 BLINKS	OPEN LIMIT SWITCH			MAIN LIMIT OPEN
					BAD SWITCH
5 BLINKS	FALSE FLAME SENSED
6 BLINKS	COMPRESSOR			3 MIN. COMP.
	OUTPUT DELAY

COMPONENT LEGEND

ALS	AUXILIARY LIMIT SWITCH
BC	BLOWER CONTACTOR
COMP	COMPRESSOR
CM	CONDENSER MOTOR
C	CONTACTOR
EM	EVAPORATOR MOTOR
F	FUSE
FC	FAN CAPACITOR
FS	FLAME SENSOR
GND	EQUIPMENT GROUND
GV	GAS VALVE
HPS	HIGH PRESSURE SWITCH
IBR	INDOOR BLOWER RELAY
IIC	INTEGRATED IGNITION CONTROL
IGN	IGNITOR
LPS	LOW PRESSURE SWITCH
LS	LIMIT SWITCH
PLF	FEMALE PLUG/CONNECTOR
PS	PRESSURE SWITCH
RS	ROLLOUT SWITCH
TB1	TERMINAL BLOCK (24V SIGNAL)
TR	TRANSFORMER
VM	VENT MOTOR
VMR	VENT MOTOR RELAY

NOTES

1.REPLACEMENT WIRE MUST BE THE SAME SIZE AND TYPE OF INSULATION AS ORIGINAL. (USE COPPER CONDUCTOR ONLY).

2.ACCESSORY ECONOMIZER PLUG ADJACENT TO BLOWER HOUSING IN RETURN AIR COMPARTMENT. REMOVE MALE PLUG AND ATTACH FEMALE PLUG TO THE ECONOMIZER ACCESSORY.

3.L1 AND L2 ON IIC CONTROL IS 24V INPUT.

4.USE COPPER CONDUCTORS ONLY.

USE NEC CLASS 2 WIRE.

5.FOR 208 VOLT TRANSFORMER OPERATION, MOVE BLACK WIRE FROM TERMINAL 3 TO TERMINAL 2 ON TRANSFORMER.

SEE UNIT RATING PLATE FOR TYPE AND SIZE OF OVER

CURRENT PROTECTION

208-240/3/60 0140L00979 REV A

FACTORY WIRING

LINE VOLTAGE

LOW VOLTAGE

OPTIONAL

HIGH VOLTAGE

FIELD WIRING

HIGH VOLTAGE

LOW VOLTAGE

WIRE CODE

BK BLACK

BL BLUE

BR BROWN

GR GREEN

OR ORANGE PK PINK PU PURPLE RD RED WH WHITE YL YELLOW

BL/PK BLUE WITH PINK STRIP YL/PK YELLOW WITH PINK STRIP

THERMOSTAT

FIELD WIRING

NO ECONOMIZER
W	WH	W
G	GR	G
R	RD	R
Y1
Y/Y2	YL	Y
C	BL	C
TB1		STAT
WITH ECONOMIZER OPTION
W	WH	W
G	GR	G
R	RD	R
Y1	YL	Y
Y/Y2
C	BL	C
TB1		STAT
2 STAGE COOLING
W	WH	W
G	GR	G
R	RD	R
Y1	YL	Y1
Y/Y2	PK	Y2
C	BL	C
TB1		STAT

Wiring is subject to change. Always refer to the wiring diagram on the unit for the most up-to-date wiring.

55