Graco 220-569 manual Fire And Explosion Hazard, Toxic Fluid Hazard

Page 5
FIRE AND EXPLOSION HAZARD

TOXIC FLUID HAZARD WARNING

FIRE AND EXPLOSION HAZARD

Improper grounding, poor ventilation, open flames or sparks can cause a hazardous condition and re- sult in a fire or explosion and serious injury.

DGround the equipment and the object being sprayed. Refer to Grounding on page 7.

DIf there is any static sparking or you feel an electric shock while using this equipment, stop spray- ing/dispensing immediately. Do not use the equipment until you identify and correct the problem.

DProvide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid be- ing sprayed/dispensed.

DKeep the spray/dispense area free of debris, including solvent, rags, and gasoline.

DElectrically disconnect all equipment in the spray/dispense area.

DExtinguish all open flames or pilot lights in the spray/dispense area.

DDo not smoke in the spray/dispense area.

DDo not turn on or off any light switch in the spray/dispense area while operating or if fumes are present.

DDo not operate a gasoline engine in the spray/dispense area.

TOXIC FLUID HAZARD

Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or swallowed.

DKnow the specific hazards of the fluid you are using.

DStore hazardous fluid in an approved container. Dispose of hazardous fluid according to all local, state and national guidelines.

DAlways wear protective eyewear, gloves, clothing and respirator as recommended by the fluid and solvent manufacturer.

3￿￿￿￿￿￿ 5

Image 5
Contents INSTRUCTIONS-PARTSLIST Refer to page 2 for the Table of Contents307-809 Rev. T Supersedes N and PCN R includes Rev. STable of Contents Pump Models Ratio and Type parts list pagesCARBON STEEL MODELS SEVERE-DUTYELECTROPOLISHED STAINLESS STEEL MODELSWarning Symbol SymbolsCaution Symbol EQUIPMENT MISUSE HAZARDTOXIC FLUID HAZARD FIRE AND EXPLOSION HAZARDPage Typical Installation Installation All PumpsMount the Pump PlumbingFluid Line from Pump Installation Air-PoweredPumpsAir Line to Motor Installation Air-PoweredPumps Hydraulic Power Supply Installation Hydraulic-PoweredPumpsHydraulic Supply to Motor Hydraulic Return from MotorP Q R Installation Hydraulic-PoweredPumpsOperation All Pumps Pressure Relief ProcedureBefore You Start the Pump Flush the Pump Before First UseShutdown Operation Air-PoweredPumpsStarting and Adjusting the Pump Shutdown Operation Hydraulic-PoweredPumpsStarting and Adjusting the Pump Flushing MaintenancePacking Nut Tightness Excessive Leaking at ThroatMix Tank Volume Hydraulic Power Supply CheckAir Line Lubricator Air Line FilterPROBLEM TroubleshootingSOLUTION CAUSEDisconnecting the Displacement Pump ServiceReconnecting the Displacement Pump For President air-poweredpumpsModel 236-601 Viscount I+ Pump Shown Model 220-569 Senator Pump ShownModel 220-564 President Pump Shown ModelCleaning and Inspecting Parts Disassembling the Displacement PumpRepair Kits ServiceService OUTLETINLET Service Reassembling the Displacement Pump   Side View of Outlet HousingService OUTLETCARBON STEEL PUMPS Parts President PumpsSEVERE-DUTY,ELECTROPOLISHED STAINLESS STEEL PUMPSModel 237-222,Series A, 3 1 Ratio104 SEVERE-DUTY,ELECTROPOLISHED STAINLESS STEEL PUMPSParts President Pumps CARBON STEEL PUMPSModel 220-574,Series B Assembly ProcedureModel 220-575,Series B Parts President Pumps3 1 Ratio Carbon Steel President Pump with 55 gal. drum cover and agitator3 1 Ratio Stainless Steel President Pump  Model 220-565,Series A, 3.5 1 Ratio Parts Quiet Senator PumpsModel 220-566,Series A, 5 1 Ratio Model 220-567,Series A, 2.5 1 RatioModel 220-577,Series A, 4 1 Ratio Parts Quiet Bulldog PumpsModel 220-578,Series A , 4 1 Ratio Model 239-815,Series A , 4 1 RatioPage SEVERE-DUTY,ELECTROPOLISHED STAINLESS STEEL PUMPS Parts Viscount I+ PumpsModel 236-601,Series A Model 236-605,Series A Model 236-712,Series AParts CARBON STEEL DISPLACEMENT PUMPSParts Matrix Model 220-549,Series DCARBON STEEL DISPLACEMENT PUMPS Model 220-549ShownParts Model 220-549,Series DModel 239-820,Series A for Pump Model PartsParts Matrix Model 237-220,Series A for Pump Model PartsPump Seal Kit Repair KitsPump Seal Kit Pump Seal KitSurge Stand DimensionsMounting Hole Bolt PatternUse Only Genuine Graco Parts and Accessories AccessoriesGrounding Wire and Clamp Medium Volume High-FloSurge TankPump Floor Stand Mounting Stand KitStationary Stand Wall BracketTechnical Data Maximum Working Pressure Technical DataPUMP OUTLET PRESSURE AIR CONSUMPTIONTechnical Data MPa, BAR PSI Technical DataPUMP OUTLET PRESSURE AIR CONSUMPTIONPage 3789 Technical DataMPa, BAR PUMP OUTLET PRESSUREViscount I+ Pumps, Models 236-605and Viscount I+ Pumps, Models 236-601andTechnical Data 3789Technical Data Manual Change SummaryViscount I+ Pumps, Models 236-712and FOR GRACO CANADA CUSTOMERS The Graco Warranty and DisclaimersGraco Phone Number