Graco 220-569 manual Operation Air-PoweredPumps, Starting and Adjusting the Pump, Shutdown

Page 13
Operation (Air-Powered Pumps)

Operation (Air-Powered Pumps)

Starting and Adjusting the Pump

1.Charge the surge tank, if you are using one. See the separate instruction manual, 307–707.

2.Open all shutoff valves (D).

3.Open the dispensing valve/spray gun at the last gun station and keep it open while starting the pump.

4.Open the bleed-type master air valves (M).

5.Adjust the air regulator (L) to the minimum pres- sure necessary for the pump to cycle slowly.

6.When fluid is flowing smoothly from the gun, release the gun trigger.

7.One at a time, open any other guns in the system to purge air from the lines.

8.Adjust the pump runaway valve (P) according to the instructions supplied with it.

9.Adjust the lubricator (N) according to the instruc- tions supplied with it.

NOTE: In a circulating system, the pump operates continuously until the power supply is shut off. In a direct supply system, the pump starts when the gun/ valve is opened, and stops when the gun/valve is closed. The pump always stops on the downstroke due to the vented inlet seat (32).

Starting and Adjusting the Pump WARNING

COMPONENT RUPTURE HAZARD To reduce the risk of overpressurizing your system, which could cause component rupture and serious injury,

never exceed the specified maximum air input pressure to the pump (see Technical Data on pages 40–45).

Shutdown

Shutdown WARNING

To reduce the risk of serious injury whenever you are instructed to relieve pressure, always follow the Pressure Relief Procedure on page 12.

Relieve the pressure.

￿￿￿￿￿￿￿ 1￿

Image 13
Contents INSTRUCTIONS-PARTSLIST Refer to page 2 for the Table of Contents307-809 Rev. T Supersedes N and PCN R includes Rev. STable of Contents Pump Models Ratio and Type parts list pagesCARBON STEEL MODELS SEVERE-DUTYELECTROPOLISHED STAINLESS STEEL MODELSWarning Symbol SymbolsCaution Symbol EQUIPMENT MISUSE HAZARDTOXIC FLUID HAZARD FIRE AND EXPLOSION HAZARDPage Typical Installation Installation All PumpsMount the Pump PlumbingAir Line to Motor Installation Air-PoweredPumpsFluid Line from Pump Installation Air-PoweredPumps Hydraulic Power Supply Installation Hydraulic-PoweredPumpsHydraulic Supply to Motor Hydraulic Return from MotorP Q R Installation Hydraulic-PoweredPumpsOperation All Pumps Pressure Relief ProcedureBefore You Start the Pump Flush the Pump Before First UseStarting and Adjusting the Pump Operation Air-PoweredPumpsShutdown Starting and Adjusting the Pump Operation Hydraulic-PoweredPumpsShutdown Flushing MaintenancePacking Nut Tightness Excessive Leaking at ThroatMix Tank Volume Hydraulic Power Supply CheckAir Line Lubricator Air Line FilterPROBLEM TroubleshootingSOLUTION CAUSEDisconnecting the Displacement Pump ServiceReconnecting the Displacement Pump For President air-poweredpumpsModel 236-601 Viscount I+ Pump Shown Model 220-569 Senator Pump ShownModel 220-564 President Pump Shown ModelCleaning and Inspecting Parts Disassembling the Displacement PumpRepair Kits ServiceINLET OUTLETService  Reassembling the Displacement PumpService   Side View of Outlet HousingService OUTLETCARBON STEEL PUMPS Parts President PumpsSEVERE-DUTY,ELECTROPOLISHED STAINLESS STEEL PUMPSModel 237-222,Series A, 3 1 Ratio104 SEVERE-DUTY,ELECTROPOLISHED STAINLESS STEEL PUMPSParts President Pumps CARBON STEEL PUMPSModel 220-574,Series B Assembly ProcedureModel 220-575,Series B Parts President Pumps3 1 Ratio Carbon Steel President Pump with 55 gal. drum cover and agitator3 1 Ratio Stainless Steel President Pump  Model 220-565,Series A, 3.5 1 Ratio Parts Quiet Senator PumpsModel 220-566,Series A, 5 1 Ratio Model 220-567,Series A, 2.5 1 RatioModel 220-577,Series A, 4 1 Ratio Parts Quiet Bulldog PumpsModel 220-578,Series A , 4 1 Ratio Model 239-815,Series A , 4 1 RatioPage SEVERE-DUTY,ELECTROPOLISHED STAINLESS STEEL PUMPS Parts Viscount I+ PumpsModel 236-601,Series A Model 236-605,Series A Model 236-712,Series AParts CARBON STEEL DISPLACEMENT PUMPSParts Matrix Model 220-549,Series DCARBON STEEL DISPLACEMENT PUMPS Model 220-549ShownParts Model 220-549,Series DParts Matrix PartsModel 239-820,Series A for Pump Model Model 237-220,Series A for Pump Model PartsPump Seal Kit Repair KitsPump Seal Kit Pump Seal KitSurge Stand DimensionsMounting Hole Bolt PatternUse Only Genuine Graco Parts and Accessories AccessoriesGrounding Wire and Clamp Medium Volume High-FloSurge TankPump Floor Stand Mounting Stand KitStationary Stand Wall BracketTechnical Data Maximum Working Pressure Technical DataPUMP OUTLET PRESSURE AIR CONSUMPTIONTechnical Data MPa, BAR PSI Technical DataPUMP OUTLET PRESSURE AIR CONSUMPTIONPage 3789 Technical DataMPa, BAR PUMP OUTLET PRESSUREViscount I+ Pumps, Models 236-605and Viscount I+ Pumps, Models 236-601andTechnical Data 3789Viscount I+ Pumps, Models 236-712and Manual Change SummaryTechnical Data Graco Phone Number The Graco Warranty and DisclaimersFOR GRACO CANADA CUSTOMERS